samsung LA 22A450C1 [BN64-00803A ] no diplay smps on 13.5v present.red led glowing i dont no inverter circuit i need schematic.
Announcement
Collapse
No announcement yet.
samsung LA 22A450C1
Collapse
X
-
Re: samsung LA 22A450C1
Originally posted by Rtech View PostCheck Inverter transformer secondary windings for resistance.
see here for pin out - no power to board - meter on ohms 2000
test s1 to s2 an s3 to s4 and post results.
http://lcdparts.net/TransformerDetai...ProductID=3721
Also test that green torpedo fuse F301Last edited by selldoor; 01-17-2014, 07:22 AM.Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740
Comment
-
Re: samsung LA 22A450C1
Can you read the P/N of the SMD PWM IC and the MOSFETs which drive the inverter transformer?
Also check the DC voltage on that connector where the wires go to the logic board, I can see the labeling but cannot read them. We need to find out if the inverter circuit is getting the inverter_on (BL_ON) signal or not.Last edited by budm; 01-22-2014, 10:41 PM.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
-
Re: samsung LA 22A450C1
Originally posted by aanan View PostFriend Rtech & selldoor.
i check fuse it is ok.
TR pinout s1 to s2 1.023 ohms s3 to s4 1.023 ohms
i suspect inv osc ic i need ic pin voltage.
Thanks for reply.
This is a TV and not a standalone Computer monitor,when you power on the power led should blink and come on.Connect AV signals and after power on keep pressing source(Input select) on remote,if TV is working with signals connected you should be able to hear the Audio.
I suspect the Logic board is defective which is a known failure for this model.Check 3V3,5V and 1.5V on the logic board and if all voltages are present suspect defective main board.
On this model I was not able to bring on the Back-lights by pulling up the pin from 5v on logic board.
I have recently repaired this TV motherboard with the same problem of No operation except power led blinking when operating with remote or panel switches.
Just heated the metal shielded box which has the micro processor ICs.
Samir
Comment
-
Re: samsung LA 22A450C1
"On this model I was not able to bring on the Back-lights by pulling up the pin from 5v on logic board." if you do not disconnect the BL_ON line from the main board if the BL_ON is being held LO by the main board, it will not allow the BL_ON to go HI using the resistor.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809
Comment
Comment