Philips 42" Plasma 42PF7320

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • mbates14
    Senior Member
    • May 2005
    • 169
    #41
    Re: Philips 42" Plasma 42PF7320

    Hey guys, quick question, would anyone be willing to help me out with a bad board that no one is using?

    I had one of these i set the wrong option code in and now i cant get the picture to come back to set the right option code. so i just need a board to pull the eeprom from to be able to get mine goin again.

      Comment

      • PlainBill
        Badcaps Legend
        • Feb 2009
        • 7034
        • USA
        #42
        Re: Philips 42" Plasma 42PF7320

        Originally posted by mbates14
        Hey guys, quick question, would anyone be willing to help me out with a bad board that no one is using?

        I had one of these i set the wrong option code in and now i cant get the picture to come back to set the right option code. so i just need a board to pull the eeprom from to be able to get mine goin again.
        It's not an unusual problem. Scan through the posts since the beginning of the year. Someone had the same problem. There is a code you enter via the remote after entering a special number sequence.

        You owe me one. Here's the thread. https://www.badcaps.net/forum/showthread.php?t=9751

        PlainBill
        Last edited by PlainBill; 08-25-2010, 10:52 PM.
        For a number of reasons, both health and personal, I will no longer be active on this board. Any PMs asking for assistance will be ignored.

        Never be afraid to try something new. Remember, amateurs built the ark. Professionals built the Titanic.

          Comment

          • mbates14
            Senior Member
            • May 2005
            • 169
            #43
            Re: Philips 42" Plasma 42PF7320

            yea that was me. LOL...... and i never did get a solution to it.

              Comment

              Previous 1 2 3 template Next

              Related Topics

              Collapse
              • celiabrown
                Issue with Plasma Philips 37inch chassis FTL2.1
                by celiabrown
                Hello guys,
                My Plasma Philips 37inch chassis FTL2.1 does no picture ,and goes into protection mode after 30 seconds (red led blinks at 3Hz).


                Can someone has any symptom like this ?

                Thanks​
                05-09-2024, 10:56 PM
              • spantor
                power board manual philips 55pus6482/12 715g-p01-000-0h2s
                by spantor
                Hello.

                Some components have exploded and I can't figure out the values. I have obtained the manual for this power supply for 65" but comparing components there are some differences and it is not reliable.
                Could someone leave me the power supply manual for this 55" model?
                I would be very grateful
                03-19-2024, 01:19 PM
              • jasonbay13
                Philips 37HFL5682L/F7 no standby light, incomplete service manual?
                by jasonbay13
                picked up a tv and when the power is plugged, the standby light flashes real quick then goes off. of 3.3, 12, 24v is all there but i couldnt find any 5v on the back-end board. ON/OFF is low, which it seems is what turns on the backlight so i removed the wire at the back-end board and put a 10k resistor to the 3.3v, which when plugged in brings on the backlight for a split second and also a blue light "LED1" on the inverter board, which goes off after a short time.
                am i missing something to bring on the backlight or is the inverter/ccfl gone bad? would that cause the inverter board...
                http://cerealbargain.duckdns.org
                12-01-2023, 09:55 PM
              • SMDFlea
                Philips TPM17.7E LA Chassis Service Manual
                by SMDFlea
                Philips TPM17.7E LA Chassis Service Manual

                43PUS6162/12 43PUT6162/12 43PUT6162/60 43PUS6262/12
                43PUT6262/12 49PUS6162/12 49PUT6162/12 49PUT6162/60
                49PUS6262/12 49PUT6262/12 50PUS6162/12 50PUT6162/12
                50PUS6262/12 50PUT6262/12 55PUS6162/12 55PUT6162/12
                55PUT6162/60 55PUS6262/12 55PUT6262/12 65PUS6162/12
                65PUT6162/12 65PUS6262/12 65PUT6262/12...
                06-03-2021, 06:52 AM
              • alro7779
                Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
                by alro7779
                Hello, guys!

                The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
                09-14-2025, 12:25 AM
              • Loading...
              • No more items.
              Working...