glued tv screens!,how to remove?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Newbie123
    Senior Member
    • Oct 2015
    • 58
    • uk

    #1

    glued tv screens!,how to remove?

    Hi all im starting to get tvs with glued in tv screens,can people tell me what tools they use to remove the screens?,thanks.
  • brucetv
    Badcaps Veteran
    • May 2015
    • 281
    • united states

    #2
    Re: glued tv screens!,how to remove?

    One of the safest ways I have found is to heat a Ufix bean bag up in the microwave for about 1-2 minutes and lay it on top of the panel where the adhesive is for about 3-4 minutes and slide a plastic playing card carefully underneath the panel and once it starts to slice through the adhesive leave the card in place and go onto to the next section so have the whole deck of cards ready. If it's a bezeless design the adhesive will be all the way around or on 3 sides only depending on the model. On some models you will be able to see the white sections of adhesive barely sticking out like on some Sony's so you can see where to apply safe heat to loosen the adhesive. You can get the Ufix bean bags at cell phone repair supplier's or shops or try Ebay. Good luck
    Attached Files

    Comment

    • Newbie123
      Senior Member
      • Oct 2015
      • 58
      • uk

      #3
      Re: glued tv screens!,how to remove?

      Many thanks Bruce i will try the playing cards it makes total sense.Cheers.

      Comment

      • Newbie123
        Senior Member
        • Oct 2015
        • 58
        • uk

        #4
        Re: glued tv screens!,how to remove?

        HI Bruce stupid question do you use plastic coated cards or all plastic playing cards?,thanks.

        Comment

        • anmol
          Senior Member
          • Mar 2012
          • 73
          • India

          #5
          Re: glued tv screens!,how to remove?

          all plastic playing cards

          Comment

          • brucetv
            Badcaps Veteran
            • May 2015
            • 281
            • united states

            #6
            Re: glued tv screens!,how to remove?

            I actually use both types because with the plastic coated they can bend a little in case the plastic bezel that's under the panel is slightly higher than the panel so I can get the card under there with that little bend without putting too much pressure on the panel. We do 5-8 backlight repairs a week and we keep logs on the degree of difficulty and what models have the pain in the ass two sided tape or adhesive strips. We are turning down some of the bezeless design Samsungs and some edge lit models because it's too much of a pain in the ass or too risky.

            Comment

            Related Topics

            Collapse

            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • acedogblast
              Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
              by acedogblast
              This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

              There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
              11-02-2024, 05:13 PM
            • Katz993
              iMac Display Replacement Adhesive
              by Katz993
              TL;DR: Looking for as-close-to-genuine as possible iMac Thin Panel (2012-2019) Adhesive.

              Long Rant: I run a tech shop that has a specialty in Macs. We've been doing upgrades and repairs on the thin panel iMacs as long as they've been out, and I've always had the issue of being unable to get something close to the OEM Adhesive for the Display Assembly, i.e. a 'two-part' adhesive, extremely thin but durable and can be cut easily with a thin wheel cutter. My replacement adhesive has always been essentially standard thin adhesive. For a long time, the biggest annoyance with this was having...
              03-15-2022, 10:31 AM
            • longmt1990
              Panasonic Cf-w5 bios password remove
              by longmt1990
              Hi, i have a Panasonic Cf-W5 with the bios password, I tried remove cmos but problem didnot solve.
              I uploaded the picture after remove cmos battery, It look like this is a Phoenix bios. The bios dump file in the link i attached

              Please help me remove bios password.
              Thank you so much
              07-06-2025, 10:50 PM
            • Maxpower3
              Hantek 365 Remove screen on startup
              by Maxpower3
              every time I open the tool, I have the screen that appears
              and I am always in a hurry to use it so I click and it automatically sends me a link to the manufacturer.

              It annoys me lol.

              2 solutions to remove it.

              Either you remove pic.bmp and it no longer appears so no more links when clicking.


              or else you can modify the exe to remove the .bmp


              hope this helps users...
              01-15-2025, 03:24 PM
            • Loading...
            • No more items.
            Working...