SONY KDL 43w805c does not accept commands

[Dobsuk]

Re: SONY KDL 43w805c does not accept commands

with mouse you can setting the tv as u like... the Notification graphic scale should work again after the hard reset... because its can turned off via setting.

take the batteries out from your RC in case the RC keep sending IR signal.. then use the side control panel .. you can try android APK too if you have android mobile with IR sender such galaxy S5. i think sony they have apk too to control the set via net work too.

Yeah, but the point is it stuck on the welcome screen. So, i cannot use any APK to control it via the network until the tv is not connected to the network. And my problem is not that this volume graphic is missing... The problem is that it does not accept command neither from the remote control nor from the side control panel.
Just tried with the mouse now and nothing - i can see the mouse coursor and move it for 2-3 sec and then it is freezing for few sec and so on.... Is there how to reflash the TV with USB stick even it is with the latest firmware already?

[Diah]

Re: SONY KDL 43w805c does not accept commands

So, did hard reset few times but did not try with the mouse. Will try it now. The TV is with the last firmware downloaded from sony website.

with mouse you can setting the tv as u like... the Notification graphic scale should work again after the hard reset... because its can turned off via setting.

take the batteries out from your RC in case the RC keep sending IR signal.. then use the side control panel .. you can try android APK too if you have android mobile with IR sender such galaxy S5. i think sony they have apk too to control the set via net work too.

[Dobsuk]

Re: SONY KDL 43w805c does not accept commands

its much firmware issue, as its android 5. there are update for years 2019 to this set- you need to try
1- hard reset from power & volume - then plug it in wall socket..
2- to by pass the first installation and to to apply update use air mouse with the tv. or any USB 2 mouse.

So, did hard reset few times but did not try with the mouse. Will try it now. The TV is with the last firmware downloaded from sony website.

[nomoresonys]

Re: SONY KDL 43w805c does not accept commands

Did you try Diah's suggestion in post #5?

[dick_barton]

Re: SONY KDL 43w805c does not accept commands

Possibly this one
https://microtech-av-spares.com/

[Dobsuk]

Re: SONY KDL 43w805c does not accept commands

Only one company i know in the UK that can repair main board .

I believe they advertise service on E BAY .

Company name is Micro tech .

Are you talking about this one? I am looking to buy another one but it looks they are not very cheap.... Just wanted to make sure that this is the problem

[Diah]

Re: SONY KDL 43w805c does not accept commands

its much firmware issue, as its android 5. there are update for years 2019 to this set- you need to try
1- hard reset from power & volume - then plug it in wall socket..
2- to by pass the first installation and to to apply update use air mouse with the tv. or any USB 2 mouse.

[Dobsuk]

Re: SONY KDL 43w805c does not accept commands

If you disconnect the wifi connector does that help. I think it's connected to the IR sensor module.?

IR SENSOR WIFI MODULE SIDE CONTROL BUTTONS FOR 43" SONY BRAVIA KDL-43W805C TV

Yeah i tried to disconnect each part one by one but nothing

[zen]

Re: SONY KDL 43w805c does not accept commands

Only one company i know in the UK that can repair main board .

I believe they advertise service on E BAY .

Company name is Micro tech .

[dick_barton]

Re: SONY KDL 43w805c does not accept commands

If you disconnect the wifi connector does that help. I think it's connected to the IR sensor module.?

IR SENSOR WIFI MODULE SIDE CONTROL BUTTONS FOR 43" SONY BRAVIA KDL-43W805C TV

[Dobsuk]

Hi, guys. This TV stopped to accept commands and it does not matter if i am using my remote control or the buttons on the TV. It is accepting it sometimes but only once or something and then it is stopping again. Only the volume command is working even i cannot see the graphic scale every time. But the volume is working - i can adjust the volume without problems. I reset the TV few times but it is the same. Now it stuck on the Welcome Screen and i cannot move forrward. Do you think that the Main Board could be a problem?