SSL400_OE2D REV0.0 technical details ( Philips 40PFL4707)

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • genuineguy
    Member
    • Sep 2015
    • 46
    • india
    #1

    SSL400_OE2D REV0.0 technical details ( Philips 40PFL4707)

    Hello

    My philips 40PFL4707/F7 has a LED driver board SSL400_OE2

    I am looking for technical details / data sheet or any information. Nothing available on google.

    If some one has at least the pinout voltages for its connectors CN1, CN2, CN3 kindly share.
    Tags: None
    • genuineguy
      Member
      • Sep 2015
      • 46
      • india
      #2
      Re: SSL400_OE2D REV0.0 technical details ( Philips 40PFL4707)

      Found from another thread on bad caps that this board also has part # LJ97-00229A in some other TV models.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • ahmedtou
          HOW CAN I UPDATE HL-DT-ST BD-RE GGW-H20N XA02
          by ahmedtou
          Hi everyone,
          help me please


          I have an HL-DT-ST BD-RE GGW-H20N with ROM version: XA02.



          When I tried to burn a 25GB Blu-ray disc using ImgBurn, I got an error.
          I will share all the details with you, including the disc information.



          Code:
          HL-DT-ST BD-RE  GGW-H20N XA02 (ATA)
Current Profile: BD-R

Disc Information:
Status: Empty
State of Last Session: Empty
Erasable: No
Free Sectors: 12,219,392
Free Space: 25,025,314,816 bytes
Free Time: 2715:27:17 (MM:SS:FF)
Next
          ...
          08-27-2025, 08:49 AM
        • alro7779
          Philips 32PFL4901/F8 BA4GF0F0102 2 Not getting standby led
          by alro7779
          Hello, guys!

          The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601...
          09-14-2025, 12:25 AM
        • G33RT
          Philips 8200 series 65PUS8204/12 stuck at Philips Logo
          by G33RT
          Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

          It does power up when pressing the power button.

          I already try the power button while plugin the plug with no result.
          Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

          Could this be an PSU or eMMC issue ?
          07-19-2025, 03:43 AM
        • electomech-fixer
          First post -Intel NUC 10i5 -BXNUC10i5FNH not powering on -IC burnt- request for IC details/datasheet
          by electomech-fixer
          Hi all,
          I came across this very active forum with knowledgeable folks on electronic circuits and components, while google searching for the details of my burnt IC marked 7603 in Intel NUC board. I joined this forum today and this is my first post here.
          I recently got an Intel NUC 10i5 and had installed Linux Mint and was using it for about a month when it died suddenly and did not power up after that.(Power Adaptor is ok). When I opened the NUC , there was a burnt IC marked 7603 (and ILCB in second line). I am unable to find the details/datasheet of this IC. I will be grateful if...
          09-15-2025, 01:42 AM
        • double_DD
          Philips curling iron - is this a common AC cable?
          by double_DD
          Hi all,

          Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
          As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.

          Not sure if this is something Philips proprietary, or a standard, but the cable plug...
          08-18-2025, 10:04 AM
        • Loading...
        • No more items.
        Working...