sony KDL-50W808c audio ok but no video

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ccaguest
    New Member
    • Sep 2019
    • 4
    • Italy

    #1

    sony KDL-50W808c audio ok but no video

    Hi friends,
    i'm struggling with sony KDL-50W808c with , but no dark screen.
    If i unplug the right lvds cable form t con ( i have 2 lvds from t con to panel )half screen is ok.
    As soon as i connect back the right lvds, i realized that all tcon voltage voltage in the way of panel goes to 0 and then dark screen.
    i have changed the tcon with same result.
    Tcon is auo T550HVN08.2.
    I would like to check for short on the card that distribuite voltage from lvds to cof flat , i but know where to measure .
    Any help or drawings or idea will be really apprettiate
    Attached Files
  • nomoresonys
    Badcaps Legend
    • Jan 2013
    • 12274
    • U.S.

    #2
    Re: sony KDL-50W808c audio ok but no video

    Check those little caps there, TV UNPLUGGED from power, ohm mode, probably looking for shorted or very low ohm could be a problem.

    Comment

    • ccaguest
      New Member
      • Sep 2019
      • 4
      • Italy

      #3
      Re: sony KDL-50W808c audio ok but no video

      Tkx for reply,i checked and removed several suspicious caps ( low resistance vs gnd ) but none helps.looks like same common tracks drain to ground .

      Comment

      • budm
        Badcaps Legend
        • Feb 2010
        • 40746
        • USA

        #4
        Re: sony KDL-50W808c audio ok but no video

        https://www.badcaps.net/forum/attach...7&d=1567854486
        So you check the cap on that tab bonding and found some low Ohm readings on some the cap? Then if you check the resistance of the empty pads where the caps are connected to, does it still show low resistance? It may be that the COF may be bad.
        Never stop learning
        Basic LCD TV and Monitor troubleshooting guides.
        http://www.badcaps.net/forum/showthr...956#post305956

        Voltage Regulator (LDO) testing:
        http://www.badcaps.net/forum/showthr...999#post300999

        Inverter testing using old CFL:
        http://www.badcaps.net/forum/showthr...er+testing+cfl

        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
        http://s807.photobucket.com/user/budm/library/

        TV Factory reset codes listing:
        http://www.badcaps.net/forum/showthread.php?t=24809

        Comment

        • ccaguest
          New Member
          • Sep 2019
          • 4
          • Italy

          #5
          Re: sony KDL-50W808c audio ok but no video

          Well, i have 3 cof in the rx part of the screen.i cant say that low resistenze is evident close to one specific cof tab. would say not full short.
          I eould try to go with power supply to check for short.but i dont know were to go with the power.schematic would help.

          Comment

          Related Topics

          Collapse

          • Hakuu
            LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
            by Hakuu
            Hi There,

            This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

            After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

            More Details

            TV Model - LG OLED77G1PUA

            Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
            07-12-2023, 02:37 PM
          • Daren87
            Sony 8K XBR-75Z8H White Screen Vertical Bars Tcon Code. Help Needed🙏
            by Daren87
            Hello everyone,

            I've recently been given a Sony 8k Z8H. It's got a white screen with two vertical black bars. At times it's given me the 5 blink Tcon code. Testing voltage on the Tcon I can see some low or missing voltage. I've done a basic visual check of cables and the COF. Not seeing anything obvious. The original Tcon seemed to have good caps until turning it over. On the bottom I found maybe 10 caps with both sides of the caps shorting to ground. I thought ok these caps and likely other components on the Tcon are shorted so let's try a replacement Tcon. I just received the...
            08-13-2023, 03:25 PM
          • iglitare
            Sony KD-75XF9005 grey Picture but Sound. TCON or panel?
            by iglitare
            Hi,

            i want to repair a Sony KD-75XF9005 TV that initially only showed a grey picture.
            Backlight seems to work, Sound (Setup menu after reset) works.
            If i dissconnect the left FFC cable from TCON to panel i have half a screen on the right. If left cable is connected always only the grey screen.
            Interchanged the cables, its always only the right side that is working. Always grey if left side is connected.
            With my small knowledge i would think at least the cables are good.

            Can this happen because of a bad tcon board?
            Or is it always a bad/shorted...
            09-04-2025, 07:13 AM
          • thelankanguy
            Sony KD-55X9000F TCON Issue
            by thelankanguy
            The TV shows a black screen with no image.
            TCON ribbon connectors were disconnected individually for image and there was no half image even.
            Later both ribbons were disconnected and TCON voltages were tested.
            12V, 3.3V, 1.8V were seen present but VONE signal reads 0V.
            There is also a short to ground in this circled inductor.
            Is this a TCON issue or something else ?...
            12-13-2024, 12:27 AM
          • bbenalmadena
            Old Sony VAIO da0hk5mb SVE1512E1E disable Radeon video card
            by bbenalmadena
            I have a Sony VAIO SVE1512E1E (motherboard da0hk5mb) video card is broken, has artifacts, I want to disable it, the processor is an I3-3110M that supposedly has an integrated Intel GPU and I want to disable the onboard Radeon so that can be used.

            I download some schematics, and tried to remove VPL1, but then the laptop starts some leds, and shut off. Should I try to lift VPL1 and VPR47 and pass a cable to one tip of VPR47 and the other back to VPU1 to see if that works or it is pointless?
            That seems to be some feedback to VPU1 and I guess if it does not detect voltage, laptop...
            08-30-2025, 10:40 AM
          • Loading...
          • No more items.
          Working...