Hello to all friends of the forum. This projector will not turn on after a power surge. Disassembling it, I found the psu with burnt components, I found a large carbonized resistor, burnt smd resistors, short power mosfet, and two small smd smeared transistors, The ic switch is a ld7575ps. Do you think it is possible to go back from another scheme to the components that can be replaced since the names are not legible?
-
-
Re: projector Cheerlux CL720 with damaged psu
I can't see the pictures, use Go Advanced - click on the paper clip to attach the pictures -
Re: projector Cheerlux CL720 with damaged psu
before 3 years i got one same the Chinese LCD led projector with power board toasted at the primary AC -DC section, i tried to find component but failed,so i took all the AC-DC parts out from PCB remain only the Transformer and the DC parts of the unit and the LED. used normal power board 20W AC to 12 Volts and put the projector transformer on it to produce 12 v and 35v to led.. and its work till now.. and the LED going more bright as before too.Comment
-
Re: projector Cheerlux CL720 with damaged psu
Attached FilesComment
-
-
Re: projector Cheerlux CL720 with damaged psu
I thank you for the answer, but do I have to connect the 12v in the primary side of the transformer or in the secondary?
I noticed that in the primary and secondary side of the transformer there are more outputs, in any case this power supply works with two voltages, 12v and 35v in outputComment
-
Re: projector Cheerlux CL720 with damaged psu
i used only the hot area from the power supply and put on it the Transformer and the DC COLD area of the Proj. board. as i said. the Transformer out put only one 12v but the Proj. one had 2 35 and 12. the good things the input of Chinese power supply transformer almost the same with 4 pins so you may connect the Original TR with wire as the size and position of pin at hot area different or opposite. don't forget the OPTO of the original board to connect to the diy one you use.. look at photos IMG its yours board and other are the diy one i usedAttached FilesComment
-
-
First post -Intel NUC 10i5 -BXNUC10i5FNH not powering on -IC burnt- request for IC details/datasheetHi all,
I came across this very active forum with knowledgeable folks on electronic circuits and components, while google searching for the details of my burnt IC marked 7603 in Intel NUC board. I joined this forum today and this is my first post here.
I recently got an Intel NUC 10i5 and had installed Linux Mint and was using it for about a month when it died suddenly and did not power up after that.(Power Adaptor is ok). When I opened the NUC , there was a burnt IC marked 7603 (and ILCB in second line). I am unable to find the details/datasheet of this IC. I will be grateful if... -
This specification for the Lenovo ThinkPad P51s + ThinkPad Stack Mobile Projector Mobile workstation can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the P51s + ThinkPad Stack Mobile Projector boardview and P51s + ThinkPad Stack Mobile Projector schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum....09-06-2024, 06:11 AM
-
Hello Guys
I have a ASUS Rog strix laptop that I bought recently to fix and the previous owner spilled water on it . He brought it into a repair shop for them to check it out and instead of fixing it they damaged the battery connector of the laptop ! Other than that they damaged damaged nothing . But since the liquid damage the laptop only turns on and the keyboard lights up and then immediately turns off. I really want to repair this laptop and I also have experience in repairing phones etc and laptops and a bit of soldering but the diagnosing part is where I need help with and... -
Hi guys
This Zotac GTX 260 had a high side MOFET on one Vcore VRM phase short circuit Drain to Gate (Not short Drain to Source)
This has burnt out the drive IC L3E (ADP3110A) and also an SOT-23 device very close to the driver IC. According to the PCB markings 'Dxxx' this is likely to be a diode.
Basically the VRM has 4 phases, two powered from one 6 way connector and two powered from the other 6 way
I would assume each pair of phases are basically identical, the burnt out phase has SOT-23 devices WW1 plus the burnt one.
The good phase... -
Quick edit: forgot to add the model
Lg PF1000u projector, please admin update the title. Thanks
Hi everyone
My projector died out a couple of weeks ago.
It's not techically dead, I can turn it on and I can hear it boot it properly, can turn it off as well, the fan boots but there was no image, no led turning on at all.
Yesterday I finally had the time (too busy at work) to disassemble it.
I opened it up and found out that the led drive part of the board had a short and had burned out. The part is the dlpa3000d from...
Comment