Sharp LC46D64U Power and OPC Flash

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nomoresonys
    Badcaps Legend
    • Jan 2013
    • 12098
    • U.S.

    #21
    Re: Sharp LC46D64U Power and OPC Flash

    One guy traced his same blink code down to inverter 3. one there for 9 bucks, looks like plenty available. https://www.ebay.com/itm/Sharp-46-LC...ZG-r:rk:1:pf:0
    Last edited by nomoresonys; 11-11-2018, 10:07 PM.

    Comment

    • Icitte
      Senior Member
      • Aug 2011
      • 61

      #22
      Re: Sharp LC46D64U Power and OPC Flash

      Originally posted by nomoresonys
      One guy traced his same blink code down to inverter 3. one there for 9 bucks, looks like plenty available. https://www.ebay.com/itm/Sharp-46-LC...ZG-r:rk:1:pf:0
      there is a way to test it before?

      Comment

      • R_J
        Badcaps Legend
        • Jun 2012
        • 9535
        • Canada

        #23
        Re: Sharp LC46D64U Power and OPC Flash

        I think the manual is a bit misleading, page 62 says error is with DET_10V (pin57) of microprocessor, BUT pin 57 monitors DET_15V (page 104) Trace that back to page 120 and it monitors the UR15V from the power supply
        You might want to get the schematic for the power supply.

        What voltage do you have on the main filter C7820/21
        Check the resistance of R7641, it is a .1Ω/1W resistor that supplies B+ to Q7602 fet
        You say you replaced some parts froma SJ kit, were any of the parts you replace defective? ie shorted fets etc.
        Last edited by R_J; 11-12-2018, 06:44 PM.

        Comment

        • nomoresonys
          Badcaps Legend
          • Jan 2013
          • 12098
          • U.S.

          #24
          Re: Sharp LC46D64U Power and OPC Flash

          Originally posted by Icitte
          there is a way to test it before?
          Read it in this thread. https://www.badcaps.net/forum/showthread.php?t=41621

          Comment

          • Icitte
            Senior Member
            • Aug 2011
            • 61

            #25
            Re: Sharp LC46D64U Power and OPC Flash

            Originally posted by R_J
            I think the manual is a bit misleading, page 62 says error is with DET_10V (pin57) of microprocessor, BUT pin 57 monitors DET_15V (page 104) Trace that back to page 120 and it monitors the UR15V from the power supply
            You might want to get the schematic for the power supply.

            What voltage do you have on the main filter C7820/21
            Check the resistance of R7641, it is a .1Ω/1W resistor that supplies B+ to Q7602 fet
            You say you replaced some parts froma SJ kit, were any of the parts you replace defective? ie shorted fets etc.
            /ok I know it's been a while, but I tested the V at C7820/21 one leg is -31vdc and the other one is around 58.8vdc

            R7641 test .1ohm

            hope you will accept to help me again!

            Comment

            Related Topics

            Collapse

            • Superbee_dad
              Sharp 80” long short flash backlight error - Help
              by Superbee_dad
              Hello Sharp TV experts
              Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

              > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
              > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
              01-24-2025, 11:51 PM
            • ekozeko333
              [Help] Lenovo Yoga Slim 7-14ARE05 (DA0LS3MBAF0) – 25Q80DVN1G Flash Is All FF, USB-C PD Stuck at 5V
              by ekozeko333
              Hi all,
              I’m trying to recover a Lenovo Yoga Slim 7-14ARE05 with board DA0LS3MBAF0 Rev:F. I’ve run into an unusual issue where USB-C PD is stuck at 4.7–5V and the system won’t boot (keyboard lights flash briefly, then nothing).
              🔥 The Problem Started After Suspected ESD/PD Fault
              I experienced a power issue or ESD event through a USB-C charger
              After that, the NX20P5090 power switch was visibly burned and was replaced
              Now the PD controller always negotiates 5V @ 2A, even with known-good chargers
              🧠 What I’ve Done So Far
              Flashed...
              06-21-2025, 02:48 AM
            • corrize
              Nikon D800 camera - flash don’t work and capacitor don’t charge
              by corrize
              Hello, I'm stuck in troubleshooting…
              The flash system works like that : when the (mechanic) flash button is pressed, the flash mecanically pop up, and a circuit buck boost elevate 7v (batt) to 200-300v (?) for charging the big capacitor. And when the photo shoot button is pressed, the capacitor is discharged in the xeon light.

              In the D800, there is a first « power board » close to the battery. 2 wires (batt 7v) goes to another little « flash board ». I measured 7v, so ok.
              When I press the flash button, it's detected by the system, flash icon appear on LDC display....
              10-01-2022, 10:02 AM
            • yucel-yucel
              Sharp LC-39LE652V Nand Flash
              by yucel-yucel
              Sharp LC-39LE652V model device could not be opened due to nand software error, we rewrote the nand software and it worked. But we were able to find the software without satellite, it does not see the internal satellite. Does this model have a working satellite version and software? Thanks in advance.

              Model ; Sharp LC-39LE652V
              Panel ; V390HK1-LE6
              Mainboard ; QPWBXG135WJZZ
              04-06-2023, 04:57 AM
            • abajor
              Canon VIXIA HF S10 A read data from inernal flash memory.
              by abajor
              Hello I've had somebody bring in one of these charming little cameras to attempt retrieving data from the internal 32GB flash.
              Something is damaged inside the cameras lens assembly I can hear it clunking around and it has probably dislodged the sensor, powering up the camera gives a blank screen and the focus motor sounds like it's having a fit.
              The camera will not connect to a computer via USB in this state, I have no options no navigation, just power up and focus/zoom motor noises.

              I think my best shot is to figure out a way to read the internal flash memory outside...
              07-20-2024, 12:04 AM
            • Loading...
            • No more items.
            Working...