Sansui LCT32SD not switching on

Collapse
X
Collapse
+ More Options
Posts
 
  • Time
  • Show
Clear All
new posts
  • Grunder
    Badcaps Veteran
    • Jan 2016
    • 323
    • south africa

    #1

    Sansui LCT32SD not switching on

    Hi guys,

    I need help determining the value of two components on the power supply.
    I've included a photo of the pcb with the components high lighted.

    IC6 = L6599 Hv resonant controller Turquoise square. Vcc is pin 12 (self limiting).
    IC3 = opto couple Yellow square.
    Trans 5. 2SA1815 (on top of pcb) marked Green. measured okay.
    Trans 6. 2SA1015 (on top of pcb) marked Blue. Short/ replaced.
    Diode 9. (on top of pcb) marked yellow. okay.
    R30. determine value. marked Red. burned beyond recognition.
    Zener diode determine value. marked Red. short No inscription.

    I tried a 1 ohm (feed resistor?) in position R30. and 5v8 for the Zener.
    But set wouldnt switch on and both slowly got hot and burned black.

    I tried electro tanya for the diagram, but no luck.

    I'm hoping one of the guys on BADCAPS with design knowledge, might be able to determine the values. Thanks.

    I forgot to say the 5v stby is there, and the psu-on does appear when pressing standby button, with led going from red to green. I reckon IC 6 isn't getting a supply, so it cant drive the transformer responsible for generating the 9,12 & 24v rails
    Attached Files
  • Grunder
    Badcaps Veteran
    • Jan 2016
    • 323
    • south africa

    #2
    Re: Sansui LCT32SD not switching on

    Anybody?

    Comment

    • Grunder
      Badcaps Veteran
      • Jan 2016
      • 323
      • south africa

      #3
      Re: Sansui LCT32SD not switching on

      Hi Guys,

      Took a chance and done a little experimentation.

      Replaced the burned resistor with a 120 ohm 1/4 watt resistor (photo 1)
      Replaced the shorted zener with a 12v zener.

      Set now switches on (backlights on), and working perfectly! (Photo 2)

      I guess the resistor was a limiting resistor, and the first attempt using the 1 ohm allowed too much current through, burning up the zener.

      I now get 12v across the zener in standby. 11.3v when the set is running.
      I now get 10.7 volts supplied to pin 12 (Vcc) on the Hv resonant ic.
      Attached Files
      Last edited by Grunder; 01-19-2017, 08:32 AM. Reason: typo

      Comment

      • dick_barton
        Badcaps Legend
        • Aug 2015
        • 6642
        • Wales

        #4
        Re: Sansui LCT32SD not switching on

        What was IC7's part number?
        Willing to help but I'm no expert.

        Comment

        • Grunder
          Badcaps Veteran
          • Jan 2016
          • 323
          • south africa

          #5
          Re: Sansui LCT32SD not switching on

          Hi Dick,

          You might not have seen my recent post (3 min before your reply).
          I did manage to get the set running.
          I didn't identify IC 7, I also suspected IC 7 got damaged. Set has been closed up.
          Thanks response.
          Last edited by Grunder; 01-19-2017, 08:28 AM. Reason: typo

          Comment

          • dick_barton
            Badcaps Legend
            • Aug 2015
            • 6642
            • Wales

            #6
            Re: Sansui LCT32SD not switching on

            Hi, I did see your post but was thinking that the data sheet for IC7 would give typical component values to check against what you used.
            Willing to help but I'm no expert.

            Comment

            • Grunder
              Badcaps Veteran
              • Jan 2016
              • 323
              • south africa

              #7
              Re: Sansui LCT32SD not switching on

              Hi Dick, quite right, checking the specs on that ic(7) would have given me a better idea of what voltages to expect in that area.

              She's running now with no heat or burning of the components fitted, if she comes back (hope not), I will investigate further.

              Thanks for the input.
              Last edited by Grunder; 01-19-2017, 09:05 AM.

              Comment

              • dick_barton
                Badcaps Legend
                • Aug 2015
                • 6642
                • Wales

                #8
                Re: Sansui LCT32SD not switching on

                Willing to help but I'm no expert.

                Comment

                Related Topics

                Collapse

                • sam_sam_sam
                  Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                  by sam_sam_sam
                  I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                  One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                  03-31-2024, 02:12 PM
                • sam_sam_sam
                  Modification to a ZD-987 desoldering/soldering station using a external switching power supply
                  by sam_sam_sam
                  I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

                  I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
                  07-01-2024, 06:34 AM
                • caspian
                  What Zener Diodes on a Linear Power Supply
                  by caspian
                  Dear members,

                  I have a linear variable power supply with unknown brand name that I used for voltage injection.
                  Then it failed. I discovered that its transistors (Q1 and Q2) are shorted.
                  In addition, I discovered that its zener diodes are defective.
                  I can replace the burned transistors.
                  But I do not know the model of the zener diodes. the model number is not marked on the zener diodes.
                  Therefore, I cannot replace the zener diodes.
                  I do not want to test the zener diodes in a test circuit to discover their model or value.
                  no schematics are available...
                  05-26-2025, 12:38 PM
                • nev1001
                  What zener diode might fix the sound on Maestro Mayhem gaming chair?
                  by nev1001
                  Hi, I'm looking for a bit of help trying to fix the audio unit from a Maestro Mayhem 4.1 gaming chair please.

                  The chair has a few speakers and vibration motors. All was well, for a while, but now the sound is gone.

                  It may be significant that I discovered my son was powering it with a 19V laptop charger when it should run on 12V - it did fully work, for bit.

                  I think an issue could be a zener diode (or capacitor) which has shorted out.

                  The board's bluetooth input still works, the vibration motors are working, so is the line out socket but not the...
                  04-17-2025, 05:09 PM
                • sam_sam_sam
                  Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
                  by sam_sam_sam
                  I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

                  This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

                  After all of...
                  07-13-2024, 08:14 PM
                • Loading...
                • No more items.
                Working...