LG 60PV250 - Erratic shut off

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • tvtimmy
    Badcaps Legend
    • Mar 2015
    • 1160
    • usa
    #21
    Re: LG 60PV250 - Erratic shut off

    I would remove that solder and do it right. Also, resolder everything that has a rivit hole under the power supply.

      Comment

      • seismicpulse
        New Member
        • Aug 2018
        • 4
        • United States
        #22
        Re: LG 60PV250 - Erratic shut off

        Can you point me to the actual power supply? I see several small “transformers” on the main board. Also, the tv worked fine for several months but you think I should still resolder the coils on the zsus?

        Thank you!

          Comment

          • tvtimmy
            Badcaps Legend
            • Mar 2015
            • 1160
            • usa
            #23
            Re: LG 60PV250 - Erratic shut off

            Power supply is in the middle of everything. The power cord plugs into it ,or is wired to it. Yes you should fix that crappy solder. Use leaded solder.

              Comment

              • seismicpulse
                New Member
                • Aug 2018
                • 4
                • United States
                #24
                Re: LG 60PV250 - Erratic shut off

                If there’s continuity among all the coils, do they need to be resoldered?

                  Comment

                  • Shane711
                    Badcaps Veteran
                    • Dec 2014
                    • 493
                    • USA
                    #25
                    Re: LG 60PV250 - Erratic shut off

                    These posts are a little old but I can guarantee that the TV turning off into stand-by mode is most defiantly the power supply board. In most cases the TV will stay on if there is no input signal and as soon as you try to play a movie or device the TV turns off. Switching out the power fixes the issue but I have 4 of these TVs so I have at least 1 power board I will attempt to repair.

                      Comment

                      Previous 1 2 template Next

                      Related Topics

                      Collapse
                      • mosfetratus
                        macbook A2918, orange light off when shut off
                        by mosfetratus
                        When i fully shut off mac, orange light goes off and wont react to power button. I have difficult time resetting with combination "shift+control+option and power button", because it rarely works (reason unknown), when i manage to get orange light and then press power button macbook wont turn on and orange light goes off. When i hold combination with power button it turns on, and works fine if put it to sleep mode.

                        Works with battery and charges, but when i shut off i get this problem.

                        It had liquid spill. Board has no corrosion, keyboard is working, power button...
                        05-31-2024, 03:34 AM
                      • PlasMatt
                        LG 60PV450 Possible Bad YSUS Need help confirming Diagnosis
                        by PlasMatt
                        I have an LG plasma that after reading through a bunch of posts and doing some testing I believe has a bad YSUS board. The problem is that that doesn't make sense to me for some of the symptoms. The problem started yesterday. While watching a movie the TV just shut down like I pressed power. I have it hooked to a PC and use RS232 to turn it off and on so I thought maybe something had glitched there. I turned it back on and finished the movie with no problems. The same thing happened today so I checked logs to see if something in the control glitched and sent an off command but it didn't, After...
                        09-20-2025, 06:50 PM
                      • rumi409
                        LG OLED C1 Pixel Cleaning Made Picture Worse
                        by rumi409
                        ​​​​​​ Hi,

                        I'm trying to resurrect a LG OLED C1 TV that has some panel banding. I used the TCON error bypass to get a picture. I was able to update the firmware as well. But when I performed a pixel cleaning to try to get the banding out, it made the image significantly worse. I tried to undo the effects of the pixel cleaning by performing a factory reset and IN_Stop, but that didn't work. Any way to reset pixel cleaning data?...
                        1 Photo
                        11-15-2024, 01:09 AM
                      • motormayhem
                        Lenovo T460 Only Charges on One Charger
                        by motormayhem
                        Laptop Question
                        Hello,
                        I'm working on a Lenovo T460 that has been having trouble charging as of late. Its worked well since I've owned it for a few years. When I went to use it the other day it was dead and wouldn't turn on (was sitting on an Anker 65W GaN charger). After some fiddling with the charger I got it to turn on and start charging, but seemed like the charger was not working as it should (took a few plug and unplug cycles to get it to start charging).

                        A day later it was dead again and wouldn't boot/charge no matter what I did. No lights or anything when...
                        05-12-2023, 01:46 PM
                      • wolf1976
                        philips 42pfl3506 working for few seconds and after shut down
                        by wolf1976
                        hi
                        i have the above tv it turns on for few seconds and after shut down
                        can you suggest me what can be cause this problem ?
                        05-25-2024, 12:18 PM
                      • Loading...
                      • No more items.
                      Working...