thanks all for your answers
i agree for the display issue
but i cant understand why at start the problem appears only on the application like you tube and when i watch digital channels alls were fine
now it appears everywere from the start when i open the tv and without connect the anteenna...
hi
i have the above tv and the display starts distorts the display at only in applications like you tube
after and on the didital channels
now without connect the antenna only the image of itsselfs tv i have the image i have in attach
i have read in another forum someone else with similar problem with mine changes tcon card and motherboard and the problem remains
can you tell me someone what is the reason that can causes that problem ? is the same the sisplay ?...
i found the ic that drives the motor fan ceiling is the cs 5752ato
is for driving dc brushless motor
can you suggest me me a receiver with remote control with six speeds
that is compatible ?
wireless receiver for 6 speeds fan control with remote control
hi i have a receiver that is destroyed from the overvoltage i guess
my question is has three wires u v w for driving a motor fan i found an other receiver wireless from aliexpresss with the same propertiew but for dc motor
the motor fan has not label
i have an other receiver operational
In your opinion can i measure the voltage at the output ?
what do you suggest me with a simple instrument multimeter or using someone instrument more specific ?
thanks in advance...
hi as you can see and from photos i have unusual colours on tv
the problem on your opinion is caused from the filter that they missings in someone leds and likes as bright spots ?
thanks in advance...
something last i want to ask i measure the pins 4 of thermostat between them and all the pins have 0 ohm resistor between them is this logical ?
i noticed from the pcb circuit one contact is for the N signal neutral and the other contact is for the secondary signal is going to one pin of electrolytic capacitor100 uf 16volt - signal
Something is going wrong
except if and the thermostat has two contacts nc when it is not activate with common point...
ok i found the way just i want to ask if you know it has a thermostat ranco i dont know the type with 4 pins that connect 4 wires i turn the plastic knob from front and i dont hear the click probably the thermosta it doesnt work but i try to remove the thermostat now and i can do it
i am afraid to apply a lot force maby i break the plastic base is there someone tip ?...
hi to all i have the pcb you can see from the fotos
in the plug included in the red circle I have two pins that are burnt black and connected to the thermostat contact my question is how does this board come out I imagine I have to peel off the mask from the front that includes the malfunction lights etc but I don't know if I have to use heat and also what glue I will use to re-glue it and secondly what could have caused this blackening on the plug pins bad contact of the thermostat that made an arc and passed a lot of current momentarily maybe it needs to be changed...
hi on the above model i look service manual
Because has a problem the TV you cannot change the channels with the remote control but the problem is not the remote control but the same tv...
is there any univarsal wifi motherboard that supports and digital tvs ?
hi i want to convert my simple digital tv because the motherboard is dead to wifi motherboard but with the ability has and tuner for digital channels DVB-T compatible in europe
is there ?
do you have to suggest me one ?
thanks on advance...
samsung ue40d6100 has no backlight no sound and image
hi to all
on the above model of samsung i have the faults i have told already on the title
iI have standby i can from remote control open and close the tv and it seems reacts the tv when i press someone button from remote control but and with the help of a torch i cannot see anything image on the tv and no sound
any idea from someone what can i measure so i can find the problem ?
the power supply is the bn44-00482a i cannot find the service manual so i can test if the leds are ok and maby these are the cause of my problem
hi again
i want to ask if someone has a mainboard 17mb140 and tells me between the pins 7 and 8 what is the value of the smd component
because from my mistake i damage it
from the electrical plan that you can download from electrotanya seems to be S307 so its like shunt or resistance 0 ohm but i ask just to be sure and the pin 7 connects direct without resistance to pin 8...
Leave a comment: