LG Plasma panel lines

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Fleckers tv
    Fleckers TV
    • Nov 2015
    • 89
    • uk

    #1

    LG Plasma panel lines

    Sorry not Plasma LED edge backlit


    This is supposed to be the LG NO SIGNAL picture but its just scrolling lines, at first I naturally assumed panel fault ,but there is this niggling doubt in the back of my mind.....

    when I unplug the Tcon from the main board its just a plain normal backlit picture (obviousley) so does anyone else thinks its Panel ?
    Attached Files
    Last edited by Fleckers tv; 06-09-2016, 05:02 PM.
  • Fleckers tv
    Fleckers TV
    • Nov 2015
    • 89
    • uk

    #2
    Re: LG Plasma panel lines

    model attached
    Attached Files

    Comment

    • dick_barton
      Badcaps Legend
      • Aug 2015
      • 6642
      • Wales

      #3
      Re: LG Plasma panel lines

      If you unhook one of the Tcon ribbons to the panel and see if you get a clear picture then reconnect and repeat for the second ribbon.


      Edit.
      How many ribbons from the Tcon to the panel does it have. Googling appears to show 2 Tcon boards. One with 2 ribbons and one with a single ribbon to the panel.
      Last edited by dick_barton; 06-09-2016, 05:09 PM.
      Willing to help but I'm no expert.

      Comment

      • ReeceyBurger123
        Never Give Up !
        • May 2014
        • 7325
        • Britain

        #4
        Re: LG Plasma panel lines

        Mate you even said it yourself the panel is toast.
        Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

        https://www.facebook.com/Telford-Tel...7894576335359/

        Comment

        Related Topics

        Collapse

        • howardc64
          TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
          by howardc64
          All left and right refers to looking from rear of TV (or looking from front with TV upside down)
          • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
          • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
          ...
          Today, 05:17 PM
        • advant
          Driving a Sharp TCON/panel with a universal main board
          by advant
          This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

          I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
          02-03-2020, 12:25 AM
        • mmartell
          General Questions on the Relationship Between Mainboard, TCON and Panel
          by mmartell
          My goal here is to be able to use boards on hand to swap into faulty sets when the faulty board is not obvious.

          I will start by asking what is the format of the output from the mainboard and is it generic in any way or does it vary by manufacturer and/or model ?

          And as far as I know a tcon and panel must be a matching pair because the timing of the signals and the voltages required to drive the panel are specific to the panel itself. (That may be a blanket statement that isn't true in some cases where the panel creates its own sub-voltages on its panel boards?)...
          01-06-2024, 01:32 PM
        • SurrealMustard
          What parts can be salvaged from a plasma with a damaged display panel?
          by SurrealMustard
          I recently found myself the proud owner of a later-model Samsung plasma (the PN59D7000 for those keeping score at home) whose panel was, unfortunately, damaged in transport. I'm now preparing to part it out, but am curious as to whether or not any damage would have come to any of the components by attempting to power it up with the panel being broken. I read in one Avsforum thread (for whatever that's worth 😂) that the "scan driver boards" (by which I assume he means buffer boards) could be impacted by doing so. Is that actually the case? If so, since I don't intend on selling bad...
          03-09-2025, 08:29 PM
        • Lee M.
          Amazon Fire TV Omni K24NE5 tcon or panel bad?
          by Lee M.
          TV came on with BL on but blank screen. Disconnected one of the ribbon cables from tcon to panel driver board and now I have half of the screen working normally. Any way to tell if the problem is with the tcon or the panel driver board or the panel itself? Should I just replace the tcon and see what happens?
          05-12-2023, 05:47 PM
        • Loading...
        • No more items.
        Working...