Vizio VF550m t-con? problem?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mcross
    Badcaps Veteran
    • Sep 2011
    • 201
    • USA

    #1

    Vizio VF550m t-con? problem?

    I have a vizio , VF550M . After power surge tv now Has sound, has back light, at top of screen display is good for about 1/2''-3/4'' of an inch. As you can see have line vert, and horz,with washout. Flexing tv makes no change as well as wiggle of cables.
    T-con has 12v , but i have a question on the regulator at U11 its a L1117 A15 has 3.30v on input pin and 1.19v output. is that not right, sound low? Sorry about pictures, tight in here,
    Help!
    Mike
    Attached Files
  • ReeceyBurger123
    Never Give Up !
    • May 2014
    • 7325
    • Britain

    #2
    Re: Vizio VF550m t-con? problem?

    That regulator is fine. To me I would probably say failed Lcd tab bond driver meaning scrap panel. See what others think.
    Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

    https://www.facebook.com/Telford-Tel...7894576335359/

    Comment

    • mcross
      Badcaps Veteran
      • Sep 2011
      • 201
      • USA

      #3
      Re: Vizio VF550m t-con? problem?

      I have done a few tab bond temp fixes, but in this case flexing lcd makes no change
      Mike

      Comment

      Related Topics

      Collapse

      • rajbot
        No Power problem with Vizio E60-E3
        by rajbot
        Hi all:

        I have a Vizio E60-E3 I am trying to troubleshoot a no power problem with. Thanks to the help on this board and elsewhere, I was pretty sure I had narrowed it to a power board problem. The board in question is a 09-60CAP0D0-00. Image attached for reference, but not of my board (tv is put away at the moment). FWIW, no obvious looking issues with the board.

        I measured voltage at power in and on the fuse and saw 120V, so power is getting to the board.

        On the pins out to the main board, I got no voltage at all on any of the pins. I assumed this...
        03-22-2023, 08:09 AM
      • THXFX
        samsung un43nu7100 BN94-13191C/BN41-02635A boot loop problem even with tcon jumper
        by THXFX
        Hi I need help with a Samsung un43nu7100 BN94-13191C/BN41-02635A with boot loop problem even with tcon jumper.
        I've already try tape method and same happen, if I disconnect both flex from mainboard to panel tv boots normal even I hear Samsung sound.
        When I solder jumper to make t-con work with or without panel or panel cables connected it still reboot or power cycling.
        What I noticed is that there's no voltage in VHG, HAVDD, PANEL_3.3V, AVDD_17V or 12v near dc-dc chip.
        I check capacitors and diodes and didn't find any short IN MAINBOARD.
        Measured all power supply...
        03-20-2024, 03:21 AM
      • theone111
        Problem with LG Plasma 60PM6700 - Random power downs
        by theone111
        I have an LG Plasma TV 60PM6700 for the past ~12 years.

        In the last ~3-4 months I have been having some issues.
        1. Problem: It started with random picture disappearing (sound still worked).
          Frequency: Happened about once a week.
          Solution: Had to turn off TV wait a few seconds before turning it on again.
        2. Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
          Frequency: Happened about once a week.
          Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve.
        3. Problem: TV shuts down
        ...
        07-22-2024, 10:36 AM
      • x_orange90_x
        TCL 50S535 bad tcon or panel issue?
        by x_orange90_x
        Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side...
        03-29-2025, 11:02 PM
      • advant
        Driving a Sharp TCON/panel with a universal main board
        by advant
        This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

        I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
        02-03-2020, 12:25 AM
      • Loading...
      • No more items.
      Working...