how to rewire 15 pin SVGA connector

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • joshage1
    New Member
    • Aug 2007
    • 6
    #1

    how to rewire 15 pin SVGA connector

    I have an old Qnix monitor (korean made i guess) with loose wiring on its video connector. It does not display blue color but when i twist the cable it does show all colors. And I don't want to work with my computer with my right hand on the mouse and the other on the monitor cable. So I pressumed it is a loose wiring inside the cable and it was near the connector to the video card. Problem is its too difficult to rewire since its too close to the connector. So I cut the 15 pin SVGA wire from one of my damaged monitor (they say flyback not working). The cut wire has black, white, yellow, brown and blue(w/ 2 wires - shield and light blue), red(w/ 2 wires - shield and pink), grey(w/ 2 wires - shield and light grey), and a large shield wire all over those wires. Problem is I dont know the wiring diagram or has no idea about it on how to.

    I have tools like circuit tester, 40 watts soldering iron, lead, sucker, screw drivers, etc.
    Tags: None
    • gastorgrab
      Badcaps Veteran
      • May 2007
      • 320
      #2
      Re: how to rewire 15 pin SVGA connector

      Is this what your looking for?


      http://www.hardwarebook.info/VGA_%2815%29

      .

        Comment

        • joshage1
          New Member
          • Aug 2007
          • 6
          #3
          Re: how to rewire 15 pin SVGA connector

          Great help. Thanks!

          I'll try it...

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Tomylee
              No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)
              by Tomylee
              Hi everyone,

              Sorry for the person who’s going to read all this !
              I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

              While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

              During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
              07-11-2025, 11:52 AM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              ORIGINAL POWER SUPPLY BOARD
              7 Photos
              11-22-2024, 01:46 PM
            • michhak
              Toshiba Satellite M50-A keyboard connector on LA-A481P motherboard
              by michhak
              Hi guys,
              i have a damaged keyboard connector on my older Toshiba Satellite M50-A laptop. I know there is LA-A481P motherboard. In attachment pictures there is a real looking connector and i also found a schematic to the connector. But i need help with finding a real electronic part to replace the damaged connector. e.g. on aliexpress (or different page).
              It is 34pin connector and the length from pin n.1 to pin n.34 is 26mm. So it means a pitch length is 0.764 mm. I have seen connectors with 0.5mm , 0.7mm , 0.8mm and 1mm pitch length. But not with 0.75. Is it some special custom connector...
              11-17-2021, 05:45 AM
            • CG2
              Meaco Arete One / Deye Dehumidifier not working
              by CG2
              I've got a dehumidifier that has stopped working. Plug it in, press the power switch, and it beeps 5 times. Nothing showing in the display (which is just two 7 segment displays) apart from the two decimal points flashing. The model is a MeacoDry Arete One 18L, which seems to be a rebadged Deye (all the boards are marked Deye). Here's what I've got so far (details in case anyone else in future should need them).

              Starting with the power board. Mains power comes in at the red connector top left. The compressor is powered by the orange connector to the right of that and is switched by...
              Power Board Front
              5 Photos
              08-17-2024, 07:47 AM
            • m1ch43lzm
              70mai Dash Cam A510 - help identifying connector on camera module
              by m1ch43lzm
              Hi everyone
              I have a 70mai Dash Cam A510 which failed after about 3 months of being installed in my car, likely due to heat, i got it from aliexpress so no point in trying to return it for warranty (and shipping it back would cost me almost the same as a new one from ali)
              The camera would boot loop showing 70mai logo on the screen, sometimes it would boot fine then the live view would freeze or display purple lines

              I already took it apart, and found out that the camera boots fine if i unplug the camera module from the main PCB, sometimes "playing" with the connector...
              05-11-2025, 06:02 PM
            • Loading...
            • No more items.
            Working...