Dahua XVR Hard Reset, Locked 8 Channel CCTV NVR

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Dan20701
    Badcaps Veteran
    • Sep 2020
    • 204
    • United Kingdom
    #1

    Dahua XVR Hard Reset, Locked 8 Channel CCTV NVR

    Hello all just wondering if anyone knows how to do a hard reset on this model, XVR58C-21D-8CH-V1.1 ?
    There are videos on youtube for every other model but this one, I do not have the switch on the board or reset jumpers.

    https://www.youtube.com/watch?v=Ao7EwIMDx_c

    I do have 2 little pads right next to the firmware chip, I have shorted these and powered the system on and waited a wile
    with no luck. I will add picture of these 2 pads.
    I do have the bin file from the firmware if its any good to anyone maybe able to edit out the pass I am not sure.
    I will not upload unless its asked for to save space on the site.

    Any help on resetting this password please. Thanks.

    . Click image for larger version Name: Fri Feb 28 15-03-42.jpg Views: 676 Size: 239.1 KB ID: 3583359
    Tags: None
    • Diah
      Badcaps Legend
      • Feb 2013
      • 6460
      • Germany
      #2
      Pin 7 are the HOLD/RSET , which need to be low for short time or longer to reset the Flash. check this pins to the tips point you mentioned.. if not related then do it direct on PIN7

        Comment

        • Dan20701
          Badcaps Veteran
          • Sep 2020
          • 204
          • United Kingdom
          #3
          Thanks mate for giving it a go, it didn't work I done it 4 or 5 times it says to connect it for about 20 seconds on all the videos I have seen.
          I took the battery out before I started. I will give this another go tomorrow mate. Thank you.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • eccerr0r
              old X58 triple channel board... memtest86 memory speed?
              by eccerr0r
              Anyone run memory speed tests with an old X58-based triple channel 1st gen or any other >2 channel board? The one I have is a Gigabyte I think.

              Anyway I had four 4GB DDR3-1333 modules in the 6 memory slots and got around 11GB/sec memory speeds assuming that it went dual channel since it didn't have enough modules for triple channel. Now I stuck in two more 4GB modules, but they are DDR3-1600. I'm still getting 11GB/sec speeds according to memtest86...

              Just wondering, anyone do memory speed analysis on these triple (and higher) channel memory boards? Are there any...
              06-28-2025, 09:06 AM
            • spleenharvester
              Reverse engineering of 18650 4-channel tester
              by spleenharvester
              Hi friends

              I have reverse engineered this tester, schematic is attached and is complete except for capacitor values. These testers annoyingly have no model number but they are the ones you find on the first page of just about any website if you type in "18650 4-channel tester". There is also a 2-channel variant and a newer 8-channel variant. They are very cheap (about £15) and can measure voltage, current, internal resistance and capacity. They have a multicolour display for all these statistics. They also have terminal blocks so that if you want to use a breakout board...
              05-04-2025, 02:43 AM
            • mikey5791
              Help on car amplifier only one channel works
              by mikey5791
              Hi all forum members,
              Fyi, i have been working on this old model PCT-4082 (4 channel car amplifier). The owner said only one channel is working.
              My initial finding is this amp originally use Toshiba 2SA1943 and 2SC5200 transistor for its output but after opening the top casing i found it used Toshiba A1941 (pnp)and C5198(npn). I desoldered all the 4 pairs transistors and found 1 piece A1941 open(tested "OL" on all legs) and replaced the 1st pair with 2SA1943 and 2SC5200, thats why you can see in the picture it is the bigger size transistor. The other A1941 and C5198 all...
              08-06-2025, 10:36 PM
            • sheffieldyorky
              ZAB/ZAB A,B/ZYJA BLOCK DIAGRAM Acer Aspire
              by sheffieldyorky
              Hey there people
              While working on my Acer Aspire with the OS failing to load, I encountered a motherboard number of DA0ZHQMB6E 0 REV: E. I was getting nowhere fast or slow, for that matter.
              This is what I tried, but not in any order.
              Google
              YouTube
              BIOS
              Command Prompt (administrator privileges)
              >
              On Google AND YouTube, I was getting mixed messages, try this and try that, but when you cross reference the advice it is either the wrong model (even though you enter the correct search term) a YouTube case in point, with the search term "how to...
              10-25-2025, 02:22 AM
            • dicky96
              American Audio VLP1500 Distorting on one channel
              by dicky96
              Hi guys I have a VLP1500 amplifier here - one channels works fine and the other channel distorts even at low volume settings

              Protection and Clip LED are off

              There is something wrong with the BIAS voltages around T16 and T18 (in particular) on the bad channel

              I tested all diodes and transistors in this area in circuit with diode mode - both channels seem identical. Same in resistance mode across all the resistors here.

              The output DC voltages on pin1 and pin8 of the 5532D dual op amp at the input of each amplifier module are the same, and the audio...
              07-13-2022, 05:25 AM
            • Loading...
            • No more items.
            Working...