huzo, I think the genuine verytanov will do it not 100% sure but should do.
The cheap one on bay don't do the job its the same when programming the chip in an adaptor it don't work.
svod 4 100% works. hope this is some help to you.
Dan20701
Senior Member
Last Activity: 06-03-2025, 08:07 AM
Joined: 09-06-2020
Location: Southamption
-
No mate, it's still sitting here in bits may need another board or sell it for scraps.
There are not many sets of bios files online for this model, DAOX8QMB8E0 REV E
and I tested all I could find. didn't think to try a set for a another board model maybe I give this a go.
if you should fix please share.Leave a comment:
-
Hello SMDFlea thank you so much for your help, sorry I have been away for a few days, tested these files
all I get is an orange flashing led near the power supply, no post if anyone has any ideas that would be great thanks.
thanks again mate .Leave a comment:
-
Thank SMDFlea for trying to help on this one, It turns out the bios chip I have is the original.
I have got this info from the bin file, the mac looks a little odd to me.
Product Name : HP ProBook 640 G8 Notebook PC
Serial Number : 5CD1360K8Z
Product Configuration ID : 2Q013AV
BuildID : 20WWISDT601#SAK8#DAK8
FeatureByte : 3X476J6S6b7B7H7M7Q7W7m7saBaEapaqauawbUbhcAdUdpdqfAfPguhKhkjhk8mEn7nVpD.r7
System Board CT Number : PKXXL058JFM0RN
MAC Address : 88-88-88-88-87-88
I think the bios file at post 1 is a EC bios file and the one...Leave a comment:
-
Hello all, I have in a job lot a HP ProBook 640 G8, one of the bios chips is missing and I am not
sure the chip that's fitted is even the original chip looks like its been replaced.
SN, 5CD1360KBZ
MB, DAOX8QMB8E0 REV E
Is there any hope for this laptop? I have tried every set of chips I can find with no luck.
Anyone have a good working set they could share please.
Thanks.Leave a comment:
-
Thanks danito, its working fine, much appreciated mate.
After seeing the changes you mate I think I would have done it wrong.Leave a comment:
-
Sorry about that, After a bit of messing around I got this model to read at 3.3v and all seems to be ok.
Could you remove the password please, I did look at the 36010 to 36CE0 it starts off ok but at the 36CE0
it was all 00 00 00 anyway so was not sure of myself., Thanks mate.
SN, R9-0YT7E3, 20NQ-S0W600...Leave a comment:
-
Hello all, I have look in to my file around the 36010 to 36CE0 mark nothing rings a bell to me.
an someone check my reading and remove the password please.
This was a slow reading seems to take longer than mec and ite chips I do wonder if the reading is ok.
X390 Yoga (Type 20NN, 20NQ)
SN, R9-0YT7E3, 20NQ-S0W600
Motherboard, LBB-1 MB 18729-1
Thanks....Leave a comment:
-
Thanks volinakis its working great password removed too, Thanks mate.Leave a comment:
-
Hello again, it's still in a boot loop, on first boot it said final steps to updating the bios it finished rebooted
and its still the same. it shows the HP log when I hit F10 it comes up entering setup, then it reboots and
starts again doing the same thing but without the final steps to the update. the cpu get very hot wile doing this.
Any ideas ? Thanks again mate for giving it a go.Leave a comment:
-
Thanks mate will give this a go, sorry for late reply been away for a few days.Leave a comment:
-
[QUOTE=
Sorry I put in the wrong S:N, It should be, 5CG2402TFM
Sorry for being an idiot I think I also uploaded the wrong files I need to clean my desktop, Added the right ones to this post....Last edited by Dan20701; 03-25-2025, 11:11 AM.Leave a comment:
-
Hello all, Can anyone help to fix this bios please, its in a loop
shows me the HP logo at startup then it shuts off and starts again.
I think there is a password too if it can be removed please.
SN, 5CG1310GWH
MB, 6050A3419601-MB-A01
Both files in the rar file, Thanks....Leave a comment:
-
I just got all these motherboards working Maxpower3.
I had to walk away from these for 2 weeks and have a break from them.
Turns out it was the programmer I was using, I fixed the svod by replacing the usb socket on it
I was getting problems with the svod for a wile now. All fixed.
Thanks so much for all your help mate.Leave a comment:
-
Thanks mate for giving it a go, it didn't work I done it 4 or 5 times it says to connect it for about 20 seconds on all the videos I have seen.
I took the battery out before I started. I will give this another go tomorrow mate. Thank you.Leave a comment:
-
Dahua XVR Hard Reset, Locked 8 Channel CCTV NVR
Hello all just wondering if anyone knows how to do a hard reset on this model, XVR58C-21D-8CH-V1.1 ?
There are videos on youtube for every other model but this one, I do not have the switch on the board or reset jumpers.
[url]https://www.youtube.com/watch?v=Ao7EwIMDx_c[/url]
I do have 2 little pads right next to the firmware chip, I have shorted these and powered the system on and waited a wile
with no luck. I will add picture of these 2 pads.
I do have the bin file from the firmware if its any good to anyone maybe able to edit out the pass I am not... -
Thanks hoaca388 its working perfected.Leave a comment:
-
Hello all can someone help to unlock this bios please I have had several goes at at it myself with no luck
I have all the DMI info needed.
Product Name : HP EliteBook 840 G8 Notebook PC
Serial Number : 5CG1310GWH
Product ID : 336D8EA#ABU
BuildID : 21WWCVCT601#SABU#DABU
FeatureByte : 3X476J6S6b7B7H7M7Q7W7m7saBaEapaqauawbUbhcAdUdpdqfAfPguhKhkjhk8mEmwnVng.aD
System Board CT Number : PKPRT00WBFH5R9
Have uploaded top side bin file I do have them both right here if its needed the bottom one too.
Thanks so much....Leave a comment:
-
Hello Rex98, Thanks so much for sharing these files they work great no problems at all, Finally got this laptop in this morning and its all sorted.
Thanks again mate.Leave a comment:
-
Thanks hoaca388, I will get him to drop it off, I didn't want to say yes I can get it sorted and them have to tell him no I cant. it is what it is, can only try.
Will uploads the bios with S:N in a few days or so.Leave a comment:
No activity results to display
Leave a comment: