I have a Spectroniq PLTV-3250 that's dead. I did a search here and found a few threads on this power supply so before posting this I ordered a repair kit from shopjimmy that came with 6 caps and a small transistor. I also went ahead and replaced all the other caps on the board to be safe. It's still dead no light or anything. I seen in a thread a zener diode fails (ZD4) Now being kind of new at stuff I checked this diode in circuit and get 650 one way and OL the other. I also checked some other zener diodes and the have something going both ways. So my question is do I need to check these out of circuit? or do I have a bunch of bad zeners? I do have pictures of all the boards if that is needed.
-
-
Re: Spectroniq PLTV-3250
The ZD4 when it is bad, it will show low Ohms in both direction.
So you did replace the transistor?
http://s807.photobucket.com/user/bud...?sort=3&page=1
http://s807.photobucket.com/user/bud...?sort=3&page=1Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: Spectroniq PLTV-3250
Yes I replaced the little transistor it came in the kit. on the ohms setting ZD4 gets 38.93k one way and 10.61k the other (in circuit)Comment
-
Re: Spectroniq PLTV-3250
I just checked ZD3 and that reads 1.6 ohms both ways. Bad I'm thinking.Comment
-
Re: Spectroniq PLTV-3250
You can take the DC voltage reading across the Zener ZD4 to see if it has about 15V on it, Diode mode or mode is not 100% accurate.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Spectroniq PLTV-3250
I get 80.6v on one side of ZD4Comment
-
Re: Spectroniq PLTV-3250
That cannot be. Are you using the chassis as the Ground ref points?. You are working in the PRIMARY side of the circuits, put the two probes of the meter at each ends of the Zener.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Spectroniq PLTV-3250
My mistake, I was using chassis as ground. Bounces between 4.4v and 5.4v and what about what I got for ZD3?Last edited by CraigR; 03-27-2014, 12:37 PM.Comment
-
Re: Spectroniq PLTV-3250
Did the kit come with small value cap 47uf 50V for the startup cap. Do you also have any Zener Diode to try?Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Spectroniq PLTV-3250
The kit did not come with it but as I stated all the caps were replaced. I have some junk boards with zeners on them but how to I get the right voltage one?
Also I just looked and the only 47uF is a 25v.Last edited by CraigR; 03-27-2014, 01:01 PM.Comment
-
Re: Spectroniq PLTV-3250
Ok, took a chance and just guessing I used a zener out of another board and put that in ZD4 and it turned on! So now I know that will fix it so how do I measure these to make sure I have the right one?Comment
-
Re: Spectroniq PLTV-3250
Measure the voltage across that Zener. The original is 15V.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Spectroniq PLTV-3250
19.2 volts on that.Comment
-
Re: Spectroniq PLTV-3250
That is on the high side close to the limit of the IC, I would get the correct one since you now know that you do have bad Zener.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Spectroniq PLTV-3250
Received the Zener today and installed and back up and running! Thanks for all the help it is always greatly appreciated.Comment
-
Re: Spectroniq PLTV-3250
Glad to hear.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Hi, I'm looking for a bit of help trying to fix the audio unit from a Maestro Mayhem 4.1 gaming chair please.
The chair has a few speakers and vibration motors. All was well, for a while, but now the sound is gone.
It may be significant that I discovered my son was powering it with a 19V laptop charger when it should run on 12V - it did fully work, for bit.
I think an issue could be a zener diode (or capacitor) which has shorted out.
The board's bluetooth input still works, the vibration motors are working, so is the line out socket but not the... -
Dear members,
I have a linear variable power supply with unknown brand name that I used for voltage injection.
Then it failed. I discovered that its transistors (Q1 and Q2) are shorted.
In addition, I discovered that its zener diodes are defective.
I can replace the burned transistors.
But I do not know the model of the zener diodes. the model number is not marked on the zener diodes.
Therefore, I cannot replace the zener diodes.
I do not want to test the zener diodes in a test circuit to discover their model or value.
no schematics are available... -
Hi friends of electronics
What you see in the video and pictures attached is the circuit for charging the batteries of a DC motor.
The problem is that this circuit cannot charge the batteries (3 1800mAH NiMH batteries) any more. When the circuit was OK, its green LEDs lit up one at a time to show that the batteries have charged more. But now that the circuit is flawed, LEDs light up as you see in the video and at the same time successive beeps are heard.
Please help me fix this circuit.
(the datasheet of the IC: https://pdf.datasheet.live/28... -
Hello.
I have seen a short circuit tester made with 3 * 9V batteries, a voltage limiter component and a resistor connected to the probes of a multimeter.
The theory is that the meter becomes sensitive enough to read very low resistances and the lowest resistance to ground on a circuit is likely to be a short circuit in that area.
Link
The Amazing $1 Short Finder Upgraded! Convert ... - YouTube
https://www.youtube.com/watch?v=0eixDdCpiO4
My multimeter isn't normally sensitive to very small resistance, but when I put a 1 mega ohm resistor... -
Hi,
I am repairing a ups which doesn't turn on ,it has the following ICs:
SG3525 used to drive inverter mosfets.
couple of uc3483, one for the power supply and another to drive a big mosfet at the output stage(i think the technique is called boost)
A LM358 and TL074 for control mechanism and of course the uController.
The SG3525 is shutting down every time the ups is turned on.
I want your help to know the function of LM358 and TL074 in the system.
I reverse engineered the LM358 circuit and i think that one of the block(A) is used for battery level...
Comment