Sanyo DP42746

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • titan2782
    New Member
    • Dec 2012
    • 2
    • USA
    #1

    Sanyo DP42746

    Reference image: http://i.imgur.com/DhyE8tH.jpg

    I've been trying to get this TV working for some time now. I replaced the Y buffers and I repaired all of the bad capacitors. I went through and checked all the solder points and cleaned the boards.

    Last time I messed with it, the PSU would turn on and then click twice and turn off. I got it to the point where now the error LED just blinks 12 times to indicate a DC12v error. However, it only occurs when I have the white ribbon cable plugged in (marked with red X in the photo).

    If I remove the ribbon the error LED stays lit, no blinking and I can hear the speakers come on (I haven't tried audio yet, I can just hear them being ON).

    Where can I go from here? I'm not sure if it's the main board, the PSU or the y-sustain. Again, it only occurs when the white ribbon connected from the y-sustain to the main board is plugged in.

    Thanks.
    Tags: None
    • minor01
      New Member
      • Oct 2013
      • 1
      • u.s.a
      #2
      Re: Sanyo DP42746

      check the power mosfetts under the small heat sink

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Tr0ll
          T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
          by Tr0ll
          Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

          The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

          Original T-con:
          Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

          First replacement T-con:

          I thought it might be t-con and ordered new t-con from china(supposedly tested)...
          10-07-2023, 07:48 PM
        • Rubenlily
          Quick question about the ribbon
          by Rubenlily
          Hey,

          So I have horizontal lines on my TV and I'm trying to trouble shoot. My question about the ribbon is:

          When I disconnect one ribbon from the t-con I should get half picture working and other half black or something like that correct? But when I disconnect the ribbon on one side I just get a dark screen and it doesn't matter what side I disconnect. I just get the dark screen. No half working, no one half black and the other one left. Sound is playing from the TV so it's obviously on and when both sides are connected I have the picture with the horizontal lines...
          08-17-2023, 11:09 AM
        • Scincidae
          UN70NU6900FXZA Won't Boot Unless I Temporarily Disconnect Right LVDS Ribbon
          by Scincidae
          I recently was given a UN70NU6900FXZA that would only boot loop once plugged in (auto powers on when plugged in). I found that disconnecting the lower (right side) LVDS ribbon, then plugging the TV in, followed by reconnecting the lower LVDS ribbon will allow the TV to work 100% normal as far as I can tell (no lines, no discoloration, no dimming or anything like that).

          I tried the tape method on the lower LVDS ribbon and found that if I cover pins 10 and 11 (counting from the bottom up) allows the TV to boot normal but 25% screen all the way to the right side is discolored. While...
          04-24-2022, 06:00 PM
        • kca
          50" LG tv with a slightly torn ribbon cable ~ Any repair method?
          by kca
          Hello all ~

          I have this LG 50" plasma tv that is in perfect working condition except for the fact that it has one (and only one), singular torn ribbon strip on one (and only one) of the 8 orange ribbon connectors that feed from the Y-Sustain to the screen itself.

          So, as a result, there is one, singular thin black horizontal line that goes across the entire screen. Distracting enough to render the picture unwatchable for all intents and purposes.

          What I am wondering is if anyone out there has ever had any success in fixing one of these ribbon cables...
          09-24-2020, 02:07 PM
        • cj_reha
          Mystery 80s Sanyo cap - perhaps polymer?
          by cj_reha
          Hey all I've been working on a 1984 Sanyo 27" color TV which had a smattering of bad caps in the video switching circuit. I found this oddball little 1uF 25V cap which looks to me like an early polymer, but I can't find concrete info proving it. I know Sanyo was a big player in early polymer cap development and this is the time period where they were just getting on the market, so I'm wondering if anyone has crusty old datasheets that could help identify it and determine if my suspicions are right? It has the same epoxy end seal and font/formatting as some old stock Os-Cons I've got laying...
          01-06-2023, 09:24 AM
        • Loading...
        • No more items.
        Working...