Sony XBR-65Z9D won't turn on after lighting strike

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Highvoltagerchelie
    New Member
    • Nov 2023
    • 6
    • United States
    #1

    Sony XBR-65Z9D won't turn on after lighting strike

    Good afternoon. I found this forum as I was looking for troubleshooting information for my Sony z9d. A lightning strike hit very close to the house and did nearly $30,000 in electronics damage. The TV appears completely dead with no status light and no picture. I found the Sony XBR-65Z9D service manual and followed the troubleshooting steps on Pages 21-26. All checks seem normal except DC_OFF_DET check on Page 23 R420 voltage was slightly higher than 3V. It was 3.475V and C418 was slightly higher that the 5V at 5.3V.

    I proceeded to check the Power Board CN6401 connector. With all cables connected I have standby Voltage, Power On Voltage and all 12V when I plug in the TV. I do not have T_CON ON 3.3Volts nor do I have T_Con 12Volts. I disconnected all cables and provided a jumper from StandyBy Volts 3.3 to Power On and to T_Con On. T_Con 12 has 12V output now.

    I'm at a loss. I think its the BM2 board that has the fault, but not sure. Can you assist? I'm comfortable making all checks. I would like to repair at component level if possible.

    Thank you for your help!

    Click image for larger version Name: IMG_2513.jpg Views: 2 Size: 2.99 MB ID: 3155803 Click image for larger version Name: IMG_2511.jpg Views: 2 Size: 2.92 MB ID: 3155804 Click image for larger version Name: IMG_2514.jpg Views: 2 Size: 3.24 MB ID: 3155805
    SONY XBR-65Z9D SERVICE MANUAL Pdf Download
    https://www.manualslib.com
    View and Download Sony XBR-65Z9D service manual online. GN2TR CHASSIS. XBR-65Z9D lcd tv pdf manual download.
    Tags: None
    • Highvoltagerchelie
      New Member
      • Nov 2023
      • 6
      • United States
      #2
      Pictures are attached in the post, but I can't see them.

        Comment

        • EazyBone
          Badcaps Legend
          • Jun 2023
          • 1306
          • United states
          #3
          Lightning usually destroys the PSU or the main board in my research. The PSU has all correct voltages, so clearly the PSU can be ruled out. Likely your main board is busted now. If you had hdmis plugged into it or anything else plugged in, the lightning could have crept through those cords and popped the main board. Check for shorts all around the HDMI ports or whatever you had plugged in. Maybe something is burned by those ports.

          TCON on will occur when main board sends signal and since you jump tested then you should be all good. I assume you have voltages going to the LED driver board also right?

          And any voltage on the tcon fuse when plugged in on stby?


            Comment

            • Highvoltagerchelie
              New Member
              • Nov 2023
              • 6
              • United States
              #4
              I'm not sure which board is the LED driver board. I haven't removed the steel plate over the TCon board. I will check. Thank you.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • Daren87
                  Sony 8K XBR-75Z8H White Screen Vertical Bars Tcon Code. Help Needed🙏
                  by Daren87
                  Hello everyone,

                  I've recently been given a Sony 8k Z8H. It's got a white screen with two vertical black bars. At times it's given me the 5 blink Tcon code. Testing voltage on the Tcon I can see some low or missing voltage. I've done a basic visual check of cables and the COF. Not seeing anything obvious. The original Tcon seemed to have good caps until turning it over. On the bottom I found maybe 10 caps with both sides of the caps shorting to ground. I thought ok these caps and likely other components on the Tcon are shorted so let's try a replacement Tcon. I just received the...
                  08-13-2023, 03:25 PM
                • thelankanguy
                  Sony KD-55X9000F TCON Issue
                  by thelankanguy
                  The TV shows a black screen with no image.
                  TCON ribbon connectors were disconnected individually for image and there was no half image even.
                  Later both ribbons were disconnected and TCON voltages were tested.
                  12V, 3.3V, 1.8V were seen present but VONE signal reads 0V.
                  There is also a short to ground in this circled inductor.
                  Is this a TCON issue or something else ?...
                  12-13-2024, 12:27 AM
                • bbrain
                  Sony KD-55AG9 TCON?
                  by bbrain
                  Hi,

                  I have this problem with my Sony 55' AG9.
                  It flashes 4x.
                  I have found the service manual, and seems it is the TCON.

                  Before I buy a TCON can someone check the vid?



                  Thanks in advance!...
                  09-19-2024, 10:50 AM
                • rimwall
                  Sony KD-65x8500b - bad Tcon or panel?
                  by rimwall
                  Hi, hoping for some views on this one which I've not come across before. The TV generates an image that has 12 noticeable bands across it. The image is still there and accurate, but the colour (or perhaps the brightness) changes gradually across each band which creates a noticeable 'step change' at the edge of each band. Given it's a 4K TV with 2160 rows of pixels, I'm guessing the 12 bands correspond to 12 gate drivers of 180 rows each. If this guess is right, then perhaps:
                  a) all the gate drivers are malfunctioning the same way (which seems unlikely), or
                  b) the Tcon board is malfunctioning,...
                  10-24-2023, 07:58 PM
                • x_orange90_x
                  TCL 50S535 bad tcon or panel issue?
                  by x_orange90_x
                  Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side...
                  03-29-2025, 11:02 PM
                • Loading...
                • No more items.
                Working...