Re: replacementvparts.com
Tvbob, let me know if you have any luck hearing back from them. Do you have a link to the craigslist ad?
I purchased a Panasonic A board from them in mid-April. It worked but wouldn't tune digital channels over the antenna input, analog were snowy and poor quality, and HDMI didn't work. Called up and owner seemed very knowledgeable and said it was a 'handshake' issue that sometimes affects Panasonic boards and if I sent it back along with my old board they would swap the EEPROM and do any necessary programming to it for no extra charge. Said turnaround would only be a few days for the repair. About 10 days later it's not here so I call up and it's supposedly in a TV and being tested as we speak and will be shipped out. Another 10 days goes by and I call again--lost my address and they had no way to lookup who ordered a part by part number. Owner apologized and seemed genuine. Gave him my address and he said it would be shipped out. This was on June 4th. Still no board and their phone (cell) just goes to voicemail (sometimes after a ring or two, sometimes after several). Really hoping to get my board back rather than file a chargeback on my credit card. The owner did seem like a nice guy.
-
Re: replacementvparts.com
A google search showed an ad on craig's list the business for sale. owner ill.
I sent them there last email today.Leave a comment:
-
Re: replacementvparts.com
That sounds quite familiar. I wouldn't even bother giving them a couple of more days.Leave a comment:
-
Re: replacementvparts.com
Its been 15 days for me, the board I ordered shows out of stock now. I guess I will give them a couple of more days then call my credit card co. They responded to 1 out 5 emails , said oder is being processed... the phone # rolls over to a t mobile cell with the voice mail full. LOLLeave a comment:
-
Re: replacementvparts.com
I bought a couple of boards from them with no problems.Leave a comment:
-
Re: replacementvparts.com
i have not
i purchased some boards from ebayLeave a comment:
-
replacementvparts.com
xxx.replacementvparts,com has anybody used them,They have a couple of boards real cheap that I need. thanks
-
I have three identical-spec 820-01700 boards (2.6/32/512), and ALL THREE boards came to us with the same fault, from different sources: The boards don't wake from hibernation with the keyboard or lid, they ONLY wake when you press the power button. I understand this is a very minor issue, but the boards must be fixed!
We will of course begin with the obvious (checking lid signals), but I couldn't help but notice these three boards were all 32GB variants. Has anyone noticed an issue relating to these 32GB boards in particular? I of course don't think it's a RAM issue, but it's bizarre... -
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached.... -
We've now created a stack of 10 boards that have the same issue, which we suspect to be CPU-related. The issue is very simple--the board will not boot to anything, only showing the exclamatory sign inside a circle. No amount of DFU/restore, wipe/erase, etc, will resolve the issue. No boards have physical damage. We went ahead and replaced the SSD nands on two boards (one 02020, one 02016) and the issue remained exactly the same. We are considering replacing the CPU on one of the boards using a locked CPU, just so we can see if it resolves the issue.
Has anyone else run into this... -
I'm looking to upgrade several 8GB 820-00850 boards to 16GB or 32GB for personal use. I am curious what the best practice and process is for sourcing new replacement chips, and what vendor(s) you guys prefer? Another question is, how do I find compatible chips and their corresponding part/model numbers? For example, in the 820-00850 schematic, the DDR chip U2600 model listed (EDFB232A1MA) corresponds to 1x32GB chip. Of course, I would need 4x8GB chips to replace the 4x2GB chips currently on the board. How do I find compatible 8GB chips? Is it as simple as searching "BGA178 8GB 2133"...
-
Hi friends, last week I got 3 same boards for repair (NM-D562 Rev. 3.0), same problem, power button light up, but motherboard wont start.
3,3V_alw and 5V_alw, 1,8V_alw and 0,75V_alw presented on all 3 boards, no other voltages. 1,2V missing and if I checked schematic right, I need 1,2V and than can be +3VS and +5VS generated after getting SUSP_N signal from KBC? or vise versa?
I checked for low resistance on coils, no low resistance.
Anyone with same issue like me?
Thanks for any help.
Leave a comment: