smd fuse question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • is_it_a_bird
    Senior Member
    • Feb 2013
    • 59
    • United Kingdom

    #1

    smd fuse question

    Hi

    Before anyone shouts at me I know how important it is to get the correct fuse rating, but yesterday I got hold of a samsung with a back light fault, after stripping it down I found that it looks like it has had fluid damage as there was rust and tell tale signs on the top of the inverter, plug 1 was melted to the connector and the smd fuse had blown.

    I cleaned everything up and replaced the fuse, the original fuse was 3.15a 74v, I have only got 3a 63v fuses available so fitted one and the TV was playing away fine for 2 hours, it then packed up again.

    The question is in reality should this fuse work or will it do what I have mentioned and blow after a short period, or do you think the inverter or B/L may have another fault somewhere.

    I was going to pop a 4a fuse in to run the tv for a good 12hours but I dont want to burn the place down


    Thanks for any help
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #2
    Re: smd fuse question

    Depends on the "blow" characteristic of the fuse more than anything (time delay, fast blow, slow blow etc...) You didn't mention the screen size so we don't know what the current consumption might be. I would doubt the inverter has a fault.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    • is_it_a_bird
      Senior Member
      • Feb 2013
      • 59
      • United Kingdom

      #3
      Re: smd fuse question

      Cheers Tom its a 26inch samsung the board in question is a HPC-1561D (pictured) as for the characteristic then I am not to sure :o( sorry
      Attached Files

      Comment

      Related Topics

      Collapse

      • socketa
        Bestec ATX0300F5WA - fast,or slow blow, fuse?
        by socketa
        I bought a dead motherboard, and connected it to this PSU,
        Was checking the standby voltages on the motherboard, and, whilst doing so, the PSU made a loud bang with a flash of light.
        So now i truly got a bang for my bucks, and something else to try and fix.
        The fuse was blowen, and the top was blowen off of a TNY276PN chip
        The glass fuse didn't have any marking to say if it was fast or slow blow
        So i checked the marking on the PCB thinking that that would tell me,
        but it 's got a T/F8A printed on the board
        So should i get a fast blow fuse, or should...
        05-17-2022, 01:22 AM
      • sam_sam_sam
        Should I take this undertaking “ Fault & Not Work 8000W LF Split Phase Pure Sine Wave Power Inverter DC24V/AC110V”
        by sam_sam_sam
        Is it worth the time to investigate what is wrong with this inverter according to the seller they offer repair parts I asked them what parts do they offer as repair parts cost $159.00 free shipping...
        06-12-2025, 06:46 AM
      • corrize
        A funny fuse story – Lumix LX100 II
        by corrize
        Hello, I disassembled this dead camera, and found this WTF… Two fuses soldered one above the other !
        I was pretty sure nobody touched it before, but that can't be from factory. There is flux, and capacitor is probably missing.
        The other weird thing : the fuses are « G » fuse : (0.75A – 8V), seems very low. The original fuse should be « O » : (32V 2,5A).
        There is « O » mark beside. All fuses have the same mark letter on main board. So, I can deduce it's a « O » fuse.
        And this correspond to the issus I saw : when I plug the battery, I measure the voltage dropping...
        10-19-2023, 09:58 AM
      • jimbofz
        lg 32LC46 backlight inverter board fault
        by jimbofz
        Hi this oldie had no backlight .after replacing caps on 24v rail ,
        still no b/l this uses inverter type:1315 B1-16A,
        im sure ive come across the same inverter in a samsung possibly le32r88bd ?
        all t/x in board test ok ,so i fitted 15k and led to pin 4 of oz964gn ic
        this allows protect to be temporary overridden.
        b/l now comes on
        but the left hand side of pic is gradually darker than the right side
        i have the cct for the tv
        but it does not have inverter cct.
        i opened it up to inspect the ccfl tubes
        and they dont have any...
        12-19-2021, 06:58 AM
      • paulmars
        bad cap cause fuse to blow?
        by paulmars
        microwave oven Fuse blew, replacement blew too after 1\2 second.

        Following common resistance test procedures found on the web the magnetron and transformer are fine.

        The big capacitor tests open. The diode attached to it reads mostly open in one direction, although sometimes my dvm will jump down to several meg ohms for a fraction of a second. Testing in other directions reads a constantly changing value of 5xxMeg to 8xxMeg.

        Would these cause the fuse to blow?

        Emerson mld mw8987b

        Tks,
        Paul
        05-26-2022, 04:24 PM
      • Loading...
      • No more items.
      Working...