what would have shorted on this board to cause 5v to short to ground all other voltages show up after pson
Attached Files
-
-
Re: pl-p42w-10a shorted 5.3 volts
Two possibilities:
Bad output diode.
Bad ceramic cap near output.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: pl-p42w-10a shorted 5.3 volts
the cap and resistor show short when tested disconnected but theres still a short on the lineAttached FilesComment
-
-
Laptop is HP Envy x360 13-bf0013dx, hp website link, it's an i7-1250U with 8 gig onboard ram.
Platform: ipa32 la-m024p rev 1b
Originally you'd plug power supply into it and it would take up to 1.2 amps and then drop to 200 milliamps and then go back up again to 1.2, staying all the while at 5 volts. Pressing power button would results in power LED blinking amber 3 times. 3.3 volt rail, 5.1 volt rail present, main power rail 8.8 volts. Power button test pads near EC chip 2.7 volts.
I found a short on the other side:
...10-04-2025, 05:03 PM -
Hi everyone,
Brought a non functionnal PS5. Apparently only a bad PSU...
No beep, nothing.
After some tests i found this :
- PSU is fine (12 volts stable)
- 12 volts line is shorted
- DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
- By the way, nothing change. No signal, no power, no beep.
Mesuring all rails with my workbench psu (12 volts input)
- 0.00 amp drawing
- 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is... -
(If anyone has a functional boardview file of FX505DV/DU that would be helpful)
(Had 3 problems, now just 1)
I have no experience or knowledge and usage of tools to repair devices besides the entire past 12-10 days of researching, watching YouTube repair videos and troubleshooting this laptop motherboard. ChatGPT was used as a guide to ask questions.
I used boardviews of mostly FX505GD-M, and some FX505DU, FX505DD. Used schematics of FX505DU.
I had originally intended to replace the BQ24780s first (due to previous battery removal while benchmarking) but I... -
I have a dead Asus ROG gaming laptop with liquid damage. When I measure the first mosfet, there is 19V. On the second mosfet there is nothing on the input and 4.3V on the output but it is not continuously. It is going up and down.
I have read this article:
https://www.prospace20.com/2022/03/h...ad-laptop.html
Is it through that inductors can never be shorted?
I have 2 inductors near the GPU that are shorted. Does this mean that the GPU itself is shorted? How can I know for sure? -
Hi all.
This notebook was showing no signs of life.
I removed the FH52M LA-J891P mainboard and found that there was 19V at the DC jack.
However there was zero volts on the two PRB2 and PRB46 resistors immediately after the two polarity protection MOSFETs (PQB11 & PQB12).
If I remove the PQW1 MOSFET, the 19V rail starts working, and I can turn on the unit - at least I get the fans, and the power light comes on, when I simulate the power button being pressed. No display.
I tried replacing the MOSFET with a new one, but again no voltage on the...
Comment