How to replace a module for lg 50 pv 400

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • robbydon
    New Member
    • Jan 2013
    • 1
    • usa
    #1

    How to replace a module for lg 50 pv 400

    on a scale of 1 to 10 how hard is it to replace a module on a lg 50 pv 400 plasma tv ? also is the main drive board a different name for module ?
    Many thanks
    robbydon
    I forgot to mention that this is my first time trying to fix a tv i am a pc repair man
    Last edited by robbydon; 01-16-2013, 02:56 PM. Reason: important info
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • repair-it
      TOSHIBA DLP 52HM95 How to reset timer module on bulb
      by repair-it
      I replaced the bulb only on my Toshiba DLP The bulb is a TB-25. This is the first time I've done a bulb only replacement. Supposedly there is a timer module that needs to be re-calibrated or reset. I don't know where the module is located. I see some vendors selling the bulb with the housing stating module included which leads me to think the module is located inside the enclosure the bulb mounts in, but I didn't see it. Maybe it's inside the plug attached to the bulb?

      Anyway - I am seeking information on how to reset this so called module so that the lamp will operate. Apparently...
      10-11-2023, 07:18 PM
    • m1ch43lzm
      70mai Dash Cam A510 - help identifying connector on camera module
      by m1ch43lzm
      Hi everyone
      I have a 70mai Dash Cam A510 which failed after about 3 months of being installed in my car, likely due to heat, i got it from aliexpress so no point in trying to return it for warranty (and shipping it back would cost me almost the same as a new one from ali)
      The camera would boot loop showing 70mai logo on the screen, sometimes it would boot fine then the live view would freeze or display purple lines

      I already took it apart, and found out that the camera boots fine if i unplug the camera module from the main PCB, sometimes "playing" with the connector...
      05-11-2025, 06:02 PM
    • Ken123
      Replace memory module with lower density
      by Ken123
      Hello. Im playing with the idea of using a Samsung K4ZAF325BM hc14 to replace a faulty hc16 on my rx 6800

      I have some hc14 on stock but no hc16 and want to get The graphicscard going until hc16 arrives.

      Is this possible?
      If it is do you loose 1gb or 8g vram in that case?
      08-15-2022, 08:06 AM
    • AlexVG
      Replacing the WiFi module on a vacuum cleaner iROBOT i7
      by AlexVG
      Hi,
      I have had an iROBOT i7 with a camera error (error 68) version REV M, year 2018.

      I bought a liquid damaged Mainboard with WiFi module, from the same vacuum cleaner, but a different year and a different version (REV G).
      (This board does not respond, only the LEDs light up in a circle.
      The liquid damage is catastrophic and restoration is impractical).
      (I bought this board to get the WiFi module and camera).

      The boards are completely different in the installation of elements, even the connector for the WiFi module is different.

      If...
      10-22-2024, 07:20 AM
    • sam_sam_sam
      Light that has a bug zapper in bottom section of light fixture the LED light module took a crap but the zapper still works
      by sam_sam_sam
      So I got the bright idea to remove the LED light module from the fixture and put it on top of another enclosure and keep using the zapper

      The removal of light module was a successful and now I just have to cut a hole in the enclosure and put a power cord that has an on and off switch on it

      You are lucky to get about two years of service out of one before the LED module starts flicking and just stops working because it is mounted on an aluminum plate and these are hard to solder on it and it is not worth messing around with them and especially this one because it has line...
      09-07-2024, 07:26 PM
    • Loading...
    • No more items.
    Working...