Ken123
Senior Member
Last Activity: 03-01-2024, 03:12 PM
Joined: 10-29-2021
Location: Fleninge
-
I hope its a decent station if i can get hold on software...Leave a comment:
-
Im not an expert but where you had 0v, did you check for short there?Leave a comment:
-
Bird bga 5000 pc software needed
Hello.
i bought this Bird rework station but comes without software for pc. I cant find anywhere to download it and dont know the name of software.
Could anyone help me pls?
/Ken... -
Re: MSI Z97 Gaming 5 D0 post code
I have same code, also got no vcore. I seem to be missing a resistor
Anyone have a clue what value?...Leave a comment:
-
Re: Asus Z97-a power cycle, no boot no cpu voltage
Could it be an rt8065 maybe?Leave a comment:
-
Re: Asus Z97-a power cycle, no boot no cpu voltage
Found what chip it is or a suitable replacement for it?Leave a comment:
-
Re: Rtx 2080 on 2070 graphics card
I dont know if same mem chips and such. Im mostly toying with the idea if you can do swaps like that.
Bios probably needed.
But i do have a 2070 that i havent tryed to fault find and i also got a 2080 card with badly broken pcb by drop damage.
If the 2070 have a bad gpu i might try and see out of curiosity
Yes if i go that route i Will see if i can find schematics.
Sounds like pinout might be same on both gpu chipsLeave a comment:
-
Rtx 2080 on 2070 graphics card
Hello. Im curious if this will work swapping a bad 2070 gpu chip for a 2080 healthy chip?
What kind of problems might occur?
/Ken -
Re: value on resistor ps4 pro
Seems to be 22ohm on my donor bordLeave a comment:
-
Re: value on resistor ps4 pro
Fixed, rookie mistake by using wrong hdmi port 🥴Leave a comment:
-
Re: value on resistor ps4 pro
Mixid boards up a bit. Its a nvg-002 but i had a nvb-003 donor. Its slightly different but had a 1k resistor there.
No difference through.
Still wlod and its wierd because console had a bad powersupply and network port/burned components.
Fixed this and I had picture and all good.
Installed a hdd and it overheated. Forgotten clamp 🥴
After this wlod.
Guess apu is a gonerLeave a comment:
-
Re: PS4 slim immediately turns off
Check for shorts on 12v and test with good powersupply.
If good it might be APULeave a comment:
-
value on resistor ps4 pro
hello, need help with identifying resistor value by the mn864729 hdmi encoderchip on a nvb-003 board.
i lost resistor when replacing encoder.
console have wlod. hope its this resistor... -
Re: Software to analyze Video RAM faults on graphics cards?
Thanks for the tips on how to install new vram test and also windows repair.
works nice but the new amd test like rx6800 do you use rx5700?
i only have rx 5000 series and radeon 7 there.
is this correct?
[QUOTE=Fasse-sweden;1160774]Hi, I have the same problem...downloaded the linked version but that one is i english...is that correct?[/QUOTE
I dont think the language matters if its the correct version of diskgeniusRe: Software to analyze Video RAM faultsLeave a comment:
-
Re: Asus rog strix gtx 1060 6gb not recognized
Reset pin open could be a gpu problem if there isnt anything else on that line to gpu.Leave a comment:
-
Re: Replace memory module with lower density
There is only 16gb bios there. But i found a supplyer in EU and ordered some correct ones. Should in 1-2 weeks. I guess i just need to wait 🙂...Leave a comment:
-
Re: Replace memory module with lower density
Nah 😜...Leave a comment:
-
Re: Replace memory module with lower density
I was too curious. Had to try it so i just yolo
it.
It Kinda works and Kinda not. I did get image but i guess What happens is you loose 1gb and The gpu sends 2gb to that chip.
Some parts of The image gets lost.
Anyway i got to see that The graphicscard Will work when i get The new chips.
Not only a loss atleast ��Leave a comment:
-
Re: I don't know!!! Gigabyte GV-R939G1 Gaming 8GD
I think it should be ok. But maybe you need to change mosfet toLeave a comment:
No activity results to display
Leave a comment: