SAMSUNG PS42D51SX bad picture
After damage to my TV, I changed this board which was quite damaged
That picture looks, after the change of board
That picture looks, after the change of board
-
-
Re: SAMSUNG PS42D51SX bad picture
Wrong board... you need to swap the X-main, not the Y-main when you get those symptoms.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: SAMSUNG PS42D51SX bad picture
Hi Tom thank you again for the reply
Initially there was no picture, of this picture came after the change of board.
We will now look at other bord, and will order.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Check the fuse on it, if it has one.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Yes, there I checked it-ОК
The old. Y board has five blown transistorsLast edited by Stanislav; 12-15-2012, 12:25 PM.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Today came the X board ,but with it there is no change in the picture.
remove the power cabel but nothing changes in picture.
If you have any ideas please share them
Comment
-
Re: SAMSUNG PS42D51SX bad picture
Check the Yfr and Yrr settings on the new Y-main. Tweak them gradually and see if the picture improves. Also, check the Vset, Vsc and Ve voltages. In particular a low Ve can sometimes cause this.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Hello Tom
for smooth rotation of the trimmer ,picture is improving but very few.
To check the voltages I need some helpLast edited by Stanislav; 01-03-2013, 11:41 AM.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Have you adjusted Yrr too?
Post a close shot of your power supply (both the main one and the smaller sub-one), I can help you locate the test points.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
I change and Yrr picture changes but not enough.
I checked these values of Volt in the picture -ОК
This is a picture of the entire Board
Comment
-
Re: SAMSUNG PS42D51SX bad picture
I saw them
Last edited by Stanislav; 01-03-2013, 12:17 PM.Comment
-
Re: SAMSUNG PS42D51SX bad picture
OK, the first step is to adjust the VS, VA voltages so that they are within 1V of the specification. (Ideally +/-0.2V.) The specification is on the back of the plasma panel, the sticker that says NTSC/PAL.
To adjust you need to measure the voltage at the particular test point and
Once you have adjusted those post a picture of the white board adjacent to the power supply -- it has the other voltages on it which are also important for the plasma display to work properly.Attached Filesif you find these attachements useful please consider making a small donation to the site
Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
-
Re: SAMSUNG PS42D51SX bad picture
Va and Vs are perfectComment
-
Re: SAMSUNG PS42D51SX bad picture
Good. Now check Vscan and Vset. There could also be a Ve voltage, though that might only be present on newer displays.
BTW, did you ever fix the Panasonic P50G20E?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Vscan ,Vset, Ve are perfect
Panasonic me crazy too ,Work 2-3 days and then goes bad, If you leave after 5 minutes a bad job works that never damaging. sometimes do not want to Tuned ON. I do not know what to doLast edited by Stanislav; 01-03-2013, 12:47 PM.Comment
-
Re: SAMSUNG PS42D51SX bad picture
Hmm, I cannot think what is causing the issue if all the voltages are good. tieny found that he had a shorted transistor in the Yfr/Yrr area which was causing overdiffusion. You are seeing underdiffusion in this case, but either would be possible. You replaced 5 FETs but maybe that wasn't enough...
I suggested you reflow the Panasonic board, did that have any effect?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
I changed the whole board Y not only transistors.
there's something strange. I leave the TV to work 5 minutes ,coolers of Y board are HOT but coolers of X board are cold (ice) It's probably not normal
What do you mean to reflow the Panasonic boardComment
-
Re: SAMSUNG PS42D51SX bad picture
See the symptom looks exactly like a failed X board but you said you'd replaced it. Are you 100% sure it is a working board?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: SAMSUNG PS42D51SX bad picture
NО . I bought it on eBayComment
-
Re: SAMSUNG PS42D51SX bad picture
Check the fuse on it (does it have one?)Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming... -
Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic... -
I hope this is the right forum to post in despite not technically being a repair, but still a question of swapping boards.
I thought I'd explore the possibility to upgrade an existing working Samsung ue55nu7096u with the logic board (and power board if needed) of a newer model (ue55ru7105k) of the same size and appearance (and resolution). The reason being I'd like the extra inputs of that board including component in, an extra HDMI port and bluetooth. Its panel is broken so I have no use for the board otherwise.
The models launched in 2018 and 2019 respectively.... -
Samsung LN46C630K1F – Intermittent Backlight, BN44-00341B Power Board
Summary for TL-DR readers:
• Backlight is intermittent, may come on with TV boot or not. No flickering, never fails during TV on.
• Have obtained Samsung schematic & service documents - Can upload if helpful.
• Have read ALL applicable threads
• C1818 and CP820 replaced as low hanging fruit
• CN802 data taken for normal and failed BL operation. SUMMARY: Pin 2 - 5vDet = 3.52 @normal, 0.0 @BL fail. Pin 6 - EPWM = 1.631 @normal, 1.058 @BL fail.
• VCC pin (18) of PFC... -
Hi all!
I've recently run into an issue with my Samsung UN55H8000AF LED TV displaying no image. I've done quite a bit of research in terms of what could be wrong with it. Below are the steps I've taken prior to reaching out here for some assistance:
1. I've tried replacing the T-Con board (BN95-01594A), twice and have still experienced the same issue with all the boards I've tested with.
2. I've tried to remove one side of the ribbon cable that goes from the T-Con board to the panel and still not getting any image on left or right side.
3. I've checked voltages...
Comment