Need help troubleshooting LG 50PC3D

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • jettboat
    Senior Member
    • Nov 2012
    • 63
    • USA
    #21
    Re: Need help troubleshooting LG 50PC3D

    well I finally got the 3d one working the ipms 15 & 16c were open not shorted on both buffers were good

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • Tynan Dill
        Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
        by Tynan Dill
        I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

        Upon bringing it home and plugging it up, it showed a standby light.

        I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

        The screen seems to blackout and stay black, but with a flashlight I can see the display.

        With my Playstation 4 connected via HDMI, and running a game I can hear sound.

        Assuming...
        ORIGINAL POWER SUPPLY BOARD
        7 Photos
        11-22-2024, 01:46 PM
      • sam_sam_sam
        Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
        by sam_sam_sam
        I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

        This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

        After all of...
        07-13-2024, 08:14 PM
      • Nicktronic
        Samsung Power Supply Board BN44-00874F
        by Nicktronic
        Hey everyone,

        This power supply board is hard to find but there are repair kits available. This board had a blown fuse, FP801S, blown PFC MOSFET, QP802CS and ceramic cap, CP809. I replaced them with parts I already had and tested the rest of the parts that would've come in the repair kit and they were fine. I powered the board up on the bench expecting, in typical Samsung power supply board fashion, to see all my output voltages but, nothing. 0 volts on CNL801, CNM801 and CNT801. The only thing I have is 170vdc on the filter caps. No standby voltage either.

        Anybody...
        03-17-2025, 06:20 AM
      • Per Eriksson
        Samsung BN44-00808D power supply board troubleshooting
        by Per Eriksson
        Hi,
        I was given a samsung 65" lcd tv which is "dead" after a lightning strike.

        Power supply board is a BN44-00808D , also have the marking L65S6N_FSM
        Main board is a BN94-10803V

        I've made some simple test.

        With main board connected nothing happens when plugged in, no blinking lights or sounds.
        Also kept it plugged in for a while and checked on the boards with a thermal camera, no hot spots detected.

        With the main board disconnected the backlights turn on and stay on.

        Checked the voltages...
        06-01-2021, 02:51 AM
      • penangit
        Hp v193 monitor power supply board
        by penangit
        Hey everyone,hope everyone is fine, I got an issue hoping you guys can help me,

        I got a HP V193 monitor it has a E59670 now i got a few of these, been using them for long time now, however this particular monitor was blacking out for a few times then after unplugging and plugging it back in it gets back to normal until now its dead.

        I tried switching the power supply board with another similar monitor and it works,so I'm trying to fix this power supply board I got some basic in electronics as a hobbyist.

        Steps taken so far:

        Checked all...
        02-21-2023, 04:00 AM
      • Loading...
      • No more items.
      Working...