Question about Power Supply voltages

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • selldoor
    Slow Learner
    • Dec 2010
    • 7870
    #21
    Re: Question about Power Supply voltages

    Hi Yes usually in circuit then if it doesnt test correctly out of circuit before
    trying to find a replacement. I have found some more info which suggests
    36ohms may be correct- as they are both the same I would assume they're ok.
    So what next?
    Please upload pictures using attachment function when ask for help on the repair
    http://www.badcaps.net/forum/showthread.php?t=39740

      Comment

      • PTCS
        Member
        • Dec 2011
        • 15
        • United States of America
        #22
        Re: Question about Power Supply voltages

        Well I finally found the time to reassemble the TV for testing after bypassing the open circuit (JR8). Unfortunately, it did not change anything that I can tell. Still no backlight or other signs of life beyond the "power" indicator turning to blue.

        Does anybody have any further suggestions?

          Comment

          • PTCS
            Member
            • Dec 2011
            • 15
            • United States of America
            #23
            Re: Question about Power Supply voltages

            One last bump before I give up and return it as-is. Thanks to all who have tried to help.

              Comment

              Previous 1 2 template Next

              Related Topics

              Collapse
              • sam_sam_sam
                Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                by sam_sam_sam
                I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                03-31-2024, 02:12 PM
              • Tynan Dill
                Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                by Tynan Dill
                I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                Upon bringing it home and plugging it up, it showed a standby light.

                I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                The screen seems to blackout and stay black, but with a flashlight I can see the display.

                With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                Assuming...
                ORIGINAL POWER SUPPLY BOARD
                7 Photos
                11-22-2024, 01:46 PM
              • sam_sam_sam
                Modification to a ZD-987 desoldering/soldering station using a external switching power supply
                by sam_sam_sam
                I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

                I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
                07-01-2024, 06:34 AM
              • JimBanville
                Definitive technology SC 2000 subwoofer amp's power supply clicking and popping
                by JimBanville
                The sub developed a constant popping every couple seconds from woofer and power LED flickering with nothing but wall AC connected. Connecting an audio cable didn't change anything. It doesn't play but a second or two of audio in between the pops.
                Opened it up and discovered the power supply is making a faint clicking or ticking sound.
                I measured the amp's output to the woofer and it pulses up to 50mv DC to be driver. The pulses coincide with the power supply ticking/clicking.
                I measured the power supply output going to the amp board and it too has this pulsing. Voltage cycles...
                09-13-2023, 07:21 AM
              • CMCM
                Russound CA4 Power Supply Repair
                by CMCM
                Hello Everybody,

                Trying to repair a power supply from a Russound CA4 Multizone Controller (picture attached)

                Russound no longer supports it but were kind enough to provide a schematic of the power supply (pdf attached).

                The outputs marked 12v and 20v are all measuring only 1v.

                The board is clicking, which I think means it is in something called hiccup mode when the flyback transformers switches because of an internal problem or something else on the board Overloading it.

                The capacitors physically look clean (no bludgesor leaks) and...
                Yesterday, 01:12 PM
              • Loading...
              • No more items.
              Working...