Can an S42AX-YD01 replace an S42AX-YB09?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Paul678
    Badcaps Veteran
    • Nov 2011
    • 402
    #1

    Can an S42AX-YD01 replace an S42AX-YB09?

    These are plasma 42" panels.

    Are they drop-in replacements for each other?

    And why doesn't ShopJimmy.com tell you which panel each TV uses? They
    have all the board #s, why not the panels too?

    Thanks for any info.....
    Last edited by Paul678; 01-08-2012, 04:59 PM.
    Tags: None
    • PlainBill
      Badcaps Legend
      • Feb 2009
      • 7034
      • USA
      #2
      Re: Can an S42AX-YD01 replace an S42AX-YB09?

      Originally posted by Paul678
      These are plasma 42" panels.

      Are they drop-in replacements for each other?
      No

      Originally posted by Paul678
      And why doesn't ShopJimmy.com tell you which panel each TV uses? They
      have all the board #s, why not the panels too?

      Thanks for any info.....
      Ask ShopJimmy.

      PlainBill
      For a number of reasons, both health and personal, I will no longer be active on this board. Any PMs asking for assistance will be ignored.

      Never be afraid to try something new. Remember, amateurs built the ark. Professionals built the Titanic.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • eccerr0r
          Sell or Shim Solar panels?
          by eccerr0r
          Well, due to my grid tie inverter not accepting high voltages, and the fact that the lions in my solar panels are 36V (72-cell) I think I need to stick with 72-cell.

          However I have a few smaller panels that are 36, 32, and two 30-cell. The 36 and 32 together run at 75% efficiency (and subtract more with additional inefficiencies) when running in parallel with the 72-cell panels. The kicker is that the two 30s... generate 0% power when connected in parallel(!)

          So now what to do with these small panels?

          I could sell them...

          Or I could shim them....
          03-29-2025, 01:07 AM
        • chth96
          Is it no harm to replace with capacitor without ripple current rating?
          by chth96
          When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


          Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
          But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
          Rubycon YK DataSheet (b...
          04-19-2024, 05:19 AM
        • RetroComputingGrotto
          Opinions/Advice on Do/Should I replace ALL Electrolytic Capacitors on old equipment?
          by RetroComputingGrotto
          I've just been repairing some (very) old speakers with a loud hum that occurred as soon as you powered them on regardless if any actual audio is played through them. I work in a School so it's 99% likey that the Teachers have hardly ever turned the power off on them for well over 10+ years.



          As you can see the top large capacitor on the right has a bulge on the top so defincately needs replacing. As the one next to it is exactly the same capacity and voltage I planned to replace them both.


          What is your advice/opinion on whether or not on old(er)...
          04-03-2024, 08:30 AM
        • GRrHaG
          GIGABYTE 3080 TI Eagle VRM Replace
          by GRrHaG
          Hi, I try to replace a VRM Alpha & Omega on a GIGABYTE 3080 TI Eagle,
          marking BKU0 but i can't identify part number for buy it

          Someone can help me ?

          do you know here i can find Sch and brd file for this card ?...
          09-21-2025, 05:43 PM
        • chth96
          Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
          by chth96
          I have purchased an 100-240v AC/5v 2a DC adaptor from aliexpress,and a month ago It smelled burning when I plugin it powerstrip.
          Since then, This AC/DC adaptor have been out of order.
          But A few days ago,I replace 0.5 watt resistor with 1 watt resistor(1ohm) in this adapter.
          After replacing resistor,It succeed to recharge all of android phone.And When I measure voltage on the two pins of USB port,It shows 5.5v
          Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
          And Is there any possibility that it will suddenly explode as well as to be out...
          12-03-2023, 04:40 AM
        • Loading...
        • No more items.
        Working...