Proline problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • johnboy183
    Senior Member
    • May 2008
    • 119

    #1

    Proline problem

    Hi,
    Have acquired yet another project - this time a Proline LVD1983wd tv/dvd which powers up ok and then all I get is a floating box saying "scart no input" or "DVD no input" and this happens with every input source and different cables. This is a first problem of this type for me. Anyone come across this before and could guide me towards where to start?
    Regards
    Johnboy183
  • rmoody
    Learning Member
    • Jul 2011
    • 262

    #2
    Re: Proline problem

    Have you taken the back off? I would start by looking for visibly bad caps on the Main board.

    Comment

    • rmoody
      Learning Member
      • Jul 2011
      • 262

      #3
      Re: Proline problem

      Also you may want to try contacting Proline and seeing if they have any kind of firmware update for it. Could possibly be all you need.

      Comment

      • johnboy183
        Senior Member
        • May 2008
        • 119

        #4
        Re: Proline problem

        Sorry I should have said I have already been through all of the preliminaries and no obvious faults or bulged caps. The powerboard is fully working -its obviously something on the video board just not seen this particular symptom before where "no input" shows for every type of source.

        Comment

        Related Topics

        Collapse

        • ugamazing
          820-02020 Super Weird Issue: Keyboard Input Character Map "Wrong"?
          by ugamazing
          So, I have a really bizarre issue that I'm struggling to identify the cause of. Working on an 820-02020 board with some bizarre keyboard/input-source character mapping. My suspicion is a possible damaged SPI ROM (U1970), perhaps, but I'm really not sure in this case:

          1. The issue is pretty weird, but when installing MacOS, I noticed my WiFi password did not work. I quickly realized the special characters (!@#$%^& etc) were not mapping correctly.

          2. I noticed the keyboard layout/input-source is defaulting to JAPANESE every single time I restore the board. I am not...
          04-10-2024, 08:06 AM
        • hugocarmo
          Panasonic TX-24A1UN CRT Sound and Input problem.
          by hugocarmo
          Hi.

          IΒ΄ve been given an old CRT from Panasonic, itΒ΄s almost new, it was storaged and almost not used since bought.
          It is imaculate inside, almost no dust or debris inside.
          The picture is good, but I have no left sound channel, I tried all the inputs, outputs, even on headphone jack. In AV2 I hear sound from right channel but no image, on tv tuner only right sound channel, the same for AV1.
          So I started to look for a service manual, I found one, and started from the beginning.
          Most of the times the caps are the problem so I orderer all the caps for all boards,...
          04-26-2025, 07:45 PM
        • theone111
          Problem with LG Plasma 60PM6700 - Random power downs
          by theone111
          I have an LG Plasma TV 60PM6700 for the past ~12 years.

          In the last ~3-4 months I have been having some issues.
          1. Problem: It started with random picture disappearing (sound still worked).
            Frequency: Happened about once a week.
            Solution: Had to turn off TV wait a few seconds before turning it on again.
          2. Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
            Frequency: Happened about once a week.
            Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve.
          3. Problem: TV shuts down
          ...
          07-22-2024, 10:36 AM
        • falcontech
          Yamaha Msr400 Input Board Problem
          by falcontech
          Good morning everyone
          I have a problem with this input module of an active speaker of the Yamaha (MSR400), the signal transmitted by this unit and sent after the EQ module and then end up the amplification form is lower than normal, I attribute the problem to this Module because with that of the twin box works perfectly, I thought of the three capacitors highlighted in the photos and that I have not yet replaced or the operational highlighted NJM2860L, the strange thing I noticed that by trying with the jack by pulling it a little out of the normal position the earnings is normal, while...
          04-06-2023, 09:44 AM
        • Zeonalbasta
          Thinkpad X1 Carbon "LMQ-1MB 12298-2 48.4LY26.021" VCC3M problem
          by Zeonalbasta
          i have a problem with thinkpad X1 carbon gen 2 "LMQ-1MB 12298-2 48.4LY26.021"
          The laptop was turned off because the MOSFET was not transmitting voltage. After checking it turned out that the gate pin on the MOSFET was the problem, because it was producing an inappropriate voltage. and it was discovered that the problem was with the Think engine, so I decided to reprint each pin, and finally the mosfet could work properly. However, there is another problem, even though the voltage has been supplied to the laptop, it still won't turn on, there isn't even an LED indicator. After double...
          09-13-2024, 01:17 PM
        • Loading...
        • No more items.
        Working...