JVC LT-40C550 PSU Backlight Fault

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • jdawg99
    Member
    • Sep 2022
    • 11
    • United Kingdom
    #1

    JVC LT-40C550 PSU Backlight Fault

    Hi Guys,
    Wonder if I can get some advice on this please. The fault is a noticeable darker screen on one half of the TV. I have checked both arrays and they seem fine. I have swapped the led outputs on the PSU and proven it's not the LED's. There is a bad output voltage on one of the ports but seems almost like some kind of grounding issue or something. From TV chassis I get 60+ Volts on the positive of each string but if I measure across the bad one (tested on both arrays) I only get 2 ish volts. If I measure from TV chassis ground to the negative I get 32v. I have done a little video to show what I mean

    https://www.dropbox.com/s/gz4yisxm48...10011.mp4?dl=0


    The PSU is a TV3902-ZC02-01(F)) and the IC I am measuring on is a ob3368ap.

    Thanks in advance
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
      by howardc64
      • Prior owner tried a replacement main board. No difference.
      • Samsung 2x red blinking standby LED = panel fault
      • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
      • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
      • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
      ...
      07-19-2025, 10:54 PM
    • triplefour
      UN65TU700DF picture and sound but no backlight. BL tests ok but repl. PSU didnt fix!
      by triplefour
      this tv is throwing me for a loop. do samsung tvs no longer have the backlight self test feature built into the power supply?
      i tested the backlight with my LED tester and it lights up both strips. one of them reads 100v and the other reads 63.7v.
      unplugged mainboard from power supply but left backlight plugged in, and then plugged psu wall power in. expected to see backlights light up but see nothing.
      according to how ive diagnosed in the past, this would almost always be a bad power supply. replacement power supply was cheap like 20$ from ebay. but still i get not even...
      09-13-2023, 10:43 PM
    • Superbee_dad
      Sharp 80” long short flash backlight error - Help
      by Superbee_dad
      Hello Sharp TV experts
      Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

      > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
      > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
      01-24-2025, 11:51 PM
    • DanPoka
      Guide me through repairing a Dell p2210f LCD ccfl backlight monitor
      by DanPoka
      I bought this p2210f dell monitor to fix. Schematic is the same as p2210.
      Behaviour is that monitors comes on but then backlight switches off almost instantly. If I look with flashlight I can still find the "No signal message". So definitely a backlight issue. Trying to advance the issue I proved that the protection circuit is switching off the backlight by shorting out C3 and resistor to disable the INL chip then re enable by removing the short.
      This is where it gets interesting. When I disassembled the monitor to solder leads on c3 capacitor I noticed the backlight flickered...
      02-15-2025, 05:05 AM
    • cheebster
      iPad Pro 12.9 5th Gen Backlight Issue
      by cheebster
      Hello, got an iPad Pro A2378 12.9 5th gen with no backlight. Got another test unit without screen, tested the screen, still no backlight with the test unit.
      Figured out the backlight on the screen was bad, ordred a new backlight from mobilesentrix, *carefully replaced it* without damaging the lcd, oh well.
      Final result, issue is still there, the screen has no back lights. So i'm back to square one, with 3 hours less and 100$ out, issue still on the screen.
      The panel is still ok, i can see the apple in the middle of the screen when it kicks in, just no backlight.
      Anyone...
      05-20-2025, 09:17 AM
    • Loading...
    • No more items.
    Working...