Aim 32" AP321 (Rebrand) Standby but cant power on!

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • scottsman76
    Member
    • May 2017
    • 13
    • South Africa
    #1

    Aim 32" AP321 (Rebrand) Standby but cant power on!

    Hi i have a 32in with a TP.VST59S.PB702 Board.
    I get all voltages 5v, 3.3 and 12v on the 12v upgrade and 22v on the led connector, and 3.3 on power switch, but no response when trying to power on.

    If I test the power on I get a voltage drop to zero but no reaction.
    Attached Files
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4562
      • Russia
      #2
      Re: Aim 32" AP321 (Rebrand) Standby but cant power on!

      The problem may be in the firmware rally or the processor itself.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • GLISIT
          Asus Probook P5440UF-XB74 power issue
          by GLISIT
          Hi all,

          TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!


          I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!

          A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about...
          01-16-2025, 02:29 PM
        • sam_sam_sam
          Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
          by sam_sam_sam
          I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

          One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
          03-31-2024, 02:12 PM
        • SkishyIshy
          Sony Bravia XBR-65x900f: No Power, No Standby-light - however 3.3v STBY is present
          by SkishyIshy
          Hey All,

          I have a Sony 65x900f that I purchased cheap because of a no-power issue.
          I assumed that because there is no standby light visible, it would be an easy fix - however upon opening up of the unit I can confirm that the 3v3 standby voltage is making it's way from the power supply to the main board. I'm a little confused as to why there is no standby light.

          I am firstly wondering if anyone has this model of TV, or has worked on one and can give me some insight. I have tried to find a service manual for this model, to no avail - and would really appreciate...
          03-17-2021, 11:44 AM
        • AleMonti
          LG 55EG910V - no power and no standby light
          by AleMonti
          Hi everyone,
          I'm trying to troubleshoot and repair this old LG OLED curved TV, model 55EG910V.
          I did some basic troubleshooting and reviewed most related posts here, but I wasn't able to isolate the issue.

          The TV shut itself off during playback and never came back to life - the standby light remains off. My dad claims that it has happened a few times in the past but the issue resolved itself after some time. Not this one.

          After checking the basics I did the following:
          • I measured all voltages and as expected the only active supply is the 3.5V standby. It
          ...
          11-04-2024, 05:02 PM
        • noinimod
          Sony 55X900E no standby light, no power. Replaced mainboard already
          by noinimod
          No standby red light, nothing
          This Sony has a separate AC->DC power adapter supplying 19.5V to the TV power board (JK3)



          Disconnected JK3 power board from main board, checked voltages on all the pin outs

          At a few pins I can see the power supply providing 19.5V to the main board



          Based on the service manual triage.. it seems to be pointing towards the power board (JK3) being the most possible culprit


          LED light turns on when I disconnect LED driver board ribbon from mainboard (so i thought it is the mainboard,...
          12-22-2021, 12:58 AM
        • Loading...
        • No more items.
        Working...