when i plug it in it will turn on and turn right back off imediately if i hit the power button it will do the same anything you can suggest would be great thanks alot
Thanks
STLPheonix
Thanks
STLPheonix
-
-
Re: magnavox / philips 26mf231d
also i have noticed that on the right hand connector on the power supply board the number 2 pin is burnt and the wire that connects to it is burnt a bit too.. any info you can help me with would be much appreciated
Thanks
stlpheonix -
Re: magnavox / philips 26mf231d
Pictures, pictures and more pictures. Just enough to let us see what is going on here. I just want to start off by saying again - I HATE PHILIPS/MAGNAVOX. Ok, now that I got that out of my system. Please take some pics of the affected board and some of the exact area - connector. Sometimes a loose connector will arch to the board causing a buildup of carbon on the pins.The strong-minded rise to the challenge of their goals,the weak-minded BECOME HATERS
Comment
-
Re: magnavox / philips 26mf231d
ok here is the two pictures the first is of the board it self the second is the only thing that looks burnt (the pin #2) andComment
-
-
Re: magnavox / philips 26mf231d
oh dear.... iv never noticed that ya know!Comment
-
Re: magnavox / philips 26mf231d
sorry about that dont know what i was thinking lolComment
-
Re: magnavox / philips 26mf231d
Yeah the "Manage Attatchments" is the preferred method by this forum.The strong-minded rise to the challenge of their goals,the weak-minded BECOME HATERS
Comment
-
Hello,
I bought a SH Philips 55OLED804/12 TV with known defect in an attempt to repair it for personal use.
The symptoms when bought: Philips logo appears then tv turns off
Things tried so far:
1. Powering it on: Philips logo shows on the screen, sometimes with some minor artefacts then shuts down. Red status led flickers rapidly into two batches then repeats
2. Put it in recovery mode by pressing joystick down then plugging it to mains: The tv shows the logo then shows the android animation along with some minor artefacts on the screen... -
Hello, guys!
The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601... -
Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.
It does power up when pressing the power button.
I already try the power button while plugin the plug with no result.
Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.
Could this be an PSU or eMMC issue ? -
Hi is any one can help me on getting the Schematics for Magnavox MDR515H/F7 And Magnavox MDR537H/F7 PDF file thank you I really appreciate it. Just need to change some component on
the main board and the power supply board. I looked all over for the internet and I cannot find the Schematics sheet for both of them. I don't know where else to look I hope someone can help me...03-07-2025, 01:03 PM -
Hi all,
Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.
Not sure if this is something Philips proprietary, or a standard, but the cable plug...
Comment