-
-
Re: LG 70UH6350 (UB.BUSMLJr)
yes.. P801 / P802 ( 1+2) P803 (7+8) all are one line... si just plug the BL socket in place and take any one of ÖED+ as probe and messure against other VC 1-12Last edited by Diah; 02-18-2023, 12:51 AM.Comment
-
Re: LG 70UH6350 (UB.BUSMLJr)
the VC 1 to 12 you can use this hols to measure.. more easy than the socketAttached FilesComment
-
-
Re: LG 70UH6350 (UB.BUSMLJr)
black probe on chassis.. and red on vc 1 to 12Comment
-
Re: LG 70UH6350 (UB.BUSMLJr)
just do this please ..... black probe on chassis.. and red on vc 1 to 12Comment
-
Re: LG 70UH6350 (UB.BUSMLJr)
????? are you sure... check againComment
-
Re: LG 70UH6350 (UB.BUSMLJr)
yours DMM set on DC right... and level 100V DC correct.. if yes,,
you need to do this test again.. after setting the probe.. you turn on the PWB.. and ckeck the high and low... see if only VC8 play crazy readingComment
-
Re: LG 70UH6350 (UB.BUSMLJr)
OK sorry so set to 100V range lol.
All are 1.1V-1.6V but VC8 1.9V-2.0VComment
-
Re: LG 70UH6350 (UB.BUSMLJr)
?? dont hurry.. read my last postComment
-
I had a Dead Samsung UN65MU6300FXZA with Mainboard BN94-12440E
Dead / No Power / No Standby Light results after power company had three
consecutive power outages on/off/on/off/on/off after which TV was rendered unresponsive.
After exploring the issue found Mainboard was the fault. Then with research on this site determined IC1604 was the suspect. The IC1604 is a surface mounted device (SMD) EEPROM, Winbond Model 25Q40CLSIP. A read on this EEPROM came back with all FF FF FF FF FF in all registers blank and empty of data. I had a spare mainboard with intact IC1604 and utilized... -
No standby red light, nothing
This Sony has a separate AC->DC power adapter supplying 19.5V to the TV power board (JK3)
Disconnected JK3 power board from main board, checked voltages on all the pin outs
At a few pins I can see the power supply providing 19.5V to the main board
Based on the service manual triage.. it seems to be pointing towards the power board (JK3) being the most possible culprit
LED light turns on when I disconnect LED driver board ribbon from mainboard (so i thought it is the mainboard,... -
Hi All,
Need help.
I have a samsung un60j620dafxza led tv. When I plug it in it has no display, no sounds, and no standby lights.
So I opened the tv and disconnected the power to the mainboard and the backlight powered up. This according to many people says that this is a mainboard
problem. I checked the voltage coming from the stb and I read 1.3 volts on pins 1,3,5 and 7 which are low volts instead of 13 volts which i think the lcd panel
might be drawing too much power from the power supply that it prevents the right voltage going to the mainboard.... -
This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.
Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today.... -
Hi everyone,
I've got a little "problem child": my Dell Latitude 7420 2-in-1, which had a faulty mainboard.
I replaced it, but ever since, the touchscreen no longer works — and honestly, I’m running out of ideas…
In Windows Device Manager, I just see an I2C HID Device with error code 10. Sporadically, the touchscreen is recognized correctly for just a few seconds, but I haven’t been able to determine under which circumstances this happens.
The touchscreen also doesn’t work in UEFI/BIOS, although it’s enabled...
Comment