Xigmatek 500W ATX PSU went POP and stopped working

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sam_sam_sam
    Badcaps Legend
    • Jul 2011
    • 6063
    • USA

    #21
    Re: Xigmatek 500W ATX PSU went POP and stopped working

    I have not had the problem of not getting the items ordered it weather or not the item would work correctly or not and to get a seller on AliExpress to work with you about the problem is hit and miss and getting AliExpress to help you with a problem is also hit and miss

    ( and this depends on what the issue is to weather or not they will help you or not )

    Banggood is only some what better time wise sometimes and there customers service is some what better but not as good as EBay

    ( but I know that buyer that are temped to take advantage of the fact that there customer service is focused on the buyer )

    but me personally I give the seller a chance to resolve an issue with an device before getting eBay customer service involved

    ( but a seller non responsive to an issue will not give me much patience working with them )



    Alibaba.com is another story by it self I do not even want to comment on the issue I have with service for buying some items from——> but let just say that I would NOT hold my breath when I need to order something that I can not find any other place because you never know if the seller will approve your order or if you can afford the shipping cost or can you find a seller that you can buy one or two of an item
    Last edited by sam_sam_sam; 01-24-2021, 07:28 PM.

    Comment

    • momaka
      master hoarder
      • May 2008
      • 12175
      • Bulgaria

      #22
      Re: Xigmatek 500W ATX PSU went POP and stopped working

      Originally posted by sam_sam_sam
      I have not had the problem of not getting the items ordered it weather or not the item would work correctly or not and to get a seller on AliExpress to work with you about the problem is hit and miss and getting AliExpress to help you with a problem is also hit and miss
      Yeah, that's exactly what I've heard.
      With AliExp, it's hard to get back to the seller and make them work with you if there is a problem... whereas with eBay, that's usually not an issue.

      Originally posted by sam_sam_sam
      ( but I know that buyer that are temped to take advantage of the fact that there customer service is focused on the buyer )

      but me personally I give the seller a chance to resolve an issue with an device before getting eBay customer service involved
      Same.
      I don't like to take advantage of the customer service if there is no need or if seller can / is willing resolve the issue, and if there truly is a genuine issue (i.e. item not working and etc.) Some people will abuse this, though, and eBay will side with the buyer... which may not be that great of a thing for anyone looking to sell on eBay.

      Originally posted by sam_sam_sam
      but a seller non responsive to an issue will not give me much patience working with them
      Last edited by momaka; 01-26-2021, 08:55 PM.

      Comment

      Related Topics

      Collapse

      • BlackScreen_22
        Harman Kardon sub TS11 (ds15 amplifer) blows fuse and mosfets
        by BlackScreen_22
        Hi, I'll start by saying that I'm not an expert and I've reached a point where I don't know what to try/do anymore...
        Starting from the beginning: I opened this subwoofer for the first time with a very strong smell of burnt electrical components, I realize that on the amplifier board there is a hole between V+ OUT and GND about the size of a finger, the damaged components were the shorted mosfets, two damaged zener diodes and two capacitors. I bought everything, I fixed the hole by cutting the pcb and putting a piece of a perforated board.
        I had no problems connecting mosfets and capacitors,...
        08-27-2024, 12:46 PM
      • kotel studios
        Intel D865PERL - no Vcore after replacing MOSFETs and MOSFET drivers
        by kotel studios
        Hi,

        Finally got time to fix this board up.
        At first it didn't give any POST codes. Turns out it was an unsupported Celeron D cpu. After dropping in an Celery 2.6gHz the CPU came out of reset with clock signal, but still no post codes. For a while it did work when I applied pressure to the ADP3168 chip, but on next reboot the MOSFETs started to burn. Then I left it as is for months.

        Now I came back prepared. Replaced the bad MOSFETs and the ADPxx18k drivers. Now I don't get any MOSFETs blowing up issues anymore. But sadly, the Vcore is missing. The whole VRM isn't...
        04-22-2025, 05:08 AM
      • flerre
        Gainward Phantom GTX 980 - mosfets w/ integrated driver NCP5369
        by flerre
        Hi!

        Managed to get a Gainward Phantom GTX 980 in an auction for a bin with components.
        No video out so I started fault finding and found a blown fuse for 3 mosfets. Started checking for shorts and found what I think is a short through all of those 3 mosfets; 0.1 ohms between "VIN" input and "VSWH" output. All mosfets in this gpu are the same ones (NCP5369) with integrated drivers and when I tried measuring the other ones through these ports they were somewhere in the kilo-ohms range.

        So, could I safely assume all of these 3 mosfets are...
        03-13-2022, 12:14 PM
      • DrDos
        kenwood kr-6030 Mosfets?????
        by DrDos
        Hello everyone, I have decided to try and replace the mosfets in my power amp (the one with relay and left and right sides) on my kenwood kr-6030. I'm trying to get the A side of my speakers working. I have replaced all the caps in the power board and I thought why not change the mosfets. They seem to be working since I have great music coming out of the B side speakers and since I am not an electronic guru (but I am learning) I don't want to make any mistakes. The mosfets I have are listed A913 so I guess 2sa913 and 2sc1913. Can't really find those in mouser or digikey at least with the info...
        09-20-2025, 04:42 PM
      • NanoTesting
        Lenovo Ideapad 15IIL05, turns on and off with charger BUT works by injecting 20v after main mosfets
        by NanoTesting
        I got a 15-IIL05 that failed to turn on BUT IT DID TRY TO TURN ON and then turned off after 30+- seconds, i disassembled it and found a screw loose inside the case.
        With charger it turns on, fan spins but gives no image.
        Tested main mosfets no short, tested 3.3v,5v,DRAM, CPU etc and they were present.
        Reflashed BIOS, same problem.
        Replaced both main mosfets.
        Checked main mosfets again and i noticed that they closed once the laptop shut down, so i decided to bypass them and used a bench PSU to check how much power the laptop was drawing while trying to turn on, 20v@3A,...
        10-30-2024, 10:48 PM
      • Loading...
      • No more items.
      Working...