FSP FSP250-50GUB PSU arcing noise, system won't POST.

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • momaka
    master hoarder
    • May 2008
    • 12175
    • Bulgaria
    #21
    Re: FSP FSP250-50GUB PSU arcing noise, system won't POST.

    It might have been a Teapo, actually. I will try to have a look this week and maybe take a few shots too.

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • tony359
        Removing electrical noise introduced by fan
        by tony359
        Hi all,

        I am working on a sound processor, it tends to overheat so I fitted a fan inside. The fan is connected to the +15V of the PSU via a DC-DC converter based on the LM2596 to reduce the voltage to around 10.5V.

        Unfortunately the analogue circuitry is picking up the noise from the fan in two ways:
        1. The fan is close to the analogue section, the motor itself gets into the outputs so I'll have to move it somewhere else
        2. Even with the fan running outside of the case, there is still some noise which is clearly going back to the processor via power line....
        2 Photos
        11-28-2023, 05:18 AM
      • disorder
        BN44-00482B makes some arcing noise
        by disorder
        hello guys,

        need some advice here, for a BN44-00482B samsung power board
        the tv works normaly but we can here a noise comming from the power board.
        this noise is not permanent, seems like some arcs, but there is no arcs really.

        this noise comes from the bottom left of the board near the AC connector.

        and most likely from tha capacitor just after the rectifier, it is marked : 2W 474K sic 610S on it, a plastic capacitor 450V/474nF.

        if i press on it, the noise change, sometimes more higher and sometimes disappears. if i stop...
        10-22-2020, 05:35 PM
      • MegaZAC
        Onkyo TX-SR805 noise in one channel
        by MegaZAC
        Surprisingly enough, this receiver doesn't have the DSP chip issue. The HDMI board does not get hot, and sound over HDMI works fine.

        Regardless of the input, the right channel has noise that is clearly noticeable even on average volume level. The only cases when there's no noise is when VCR input is selected (some tracks on the board are damaged, maybe that's why), or if HDMI input is selected but nothing plugged into it. In all other cases, even when no input is connected I still have the noise.

        There's some logic behind it. As soon as I select an input I get only left...
        04-23-2025, 10:09 PM
      • courtcircuit
        Philips HTS8000 home cinema noise problem
        by courtcircuit
        Hello

        I have since a long time a Philips HTS8010S/01 which has been old but was doing the job.

        Since a few days, it starts by making a weird "static" nois when switches on for a few seconds to a minute and then works like a charm.
        Noise loudly outputs from the 3 channels, even if no signal is sent by the controler.DVD to the subwoofer/amp unit.

        I was thinking of a soldering that was starting to be damaged and that was only doing the job after a few seconds of heating, most probbaly on the power board
        Removed each of tyhe boards
        ...
        02-08-2025, 08:22 AM
      • karatzdi
        Denon AVR 1908, High pitch noise on Surround back Left channel after long overhaul
        by karatzdi
        Hello,

        I know some might say... just buy another one. Sell it as parts..!

        So had this AMP for quite some time. Recently I saw light smoke coming out of the AMP. Had my fire extinguisher close by. Just kidding. Turned immediately all devices off from mains.
        Let things cool a bit, and opened up the amp device. I clearly saw on the main board which hosts the 5X amp (5.1), 3 10 ohms 1W resistors had their leads looking black, while the rest of the remaining 2 x 10 ohms were brownish as being installed from factory.

        Spent some time downloading the Service...
        06-11-2024, 08:38 AM
      • Loading...
      • No more items.
      Working...