I bought this https://www.ebay.com/itm/315173036369 power supply to try to convert to a Tube radio B+ power supply I am wondering how to force it on to stay at it's highest voltage. Is there a way to make this not constant current? I need somewhere between 70 to 90vdc at I'm guessing 150ma. I am aware that the switching noise may cause interference in the radio, it is being driven by 4 3.7v lion 21760? cells with a BMS board. I basically want a dumb power supply for 90vdc which will have a cap for filtering between this and the 90v battery circuit
-
Goshen NY, USA -
get a datasheet for the chip
-
I'll try to find the info, I don't have it in hand yet, waiting for delivery. I was just wondering if someone had experience with this board.
Thanks!
ScottGoshen NY, USAComment
-
I cannot find the info, the pics online are not good enough to get the part number, I will get back to you when it arrives.Goshen NY, USAComment
-
-
Thanks for the info!
It looks like the dimming pin can be unconnected for maximum output. So one thing solved.
Somewhere I read PS on is 5v, so I think I'm in business.Goshen NY, USAComment
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming... -
I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump
One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy... -
I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails
I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time... -
I have a 15 - inch Retina MacBook Pro from the mid - 2014 model. Here is the link: https://www.badcaps.net/forum/showth...light=820-3662 . The battery broke some time ago. After I removed the battery and plugged in the original power adapter, the MBP could boot up normally. However, when I checked with IntelPowerGadget, I found that the CPU speed was limited to 0.8 GHz, and it ran very slowly. Later, I found a solution on GitHub. There is an open - source project called cputune that can set the CPU running speed. So I can now run the MBP at full speed. But another problem... -
Hello!
i got a damaged Manson NTP-5561 (60V, 1,6A DC output) and and the main issue is that the controler IC for the LCD display has a short. The controler IC PIC18F87K90 is mounted on the back of the back of the LCD. Vss-Vdd = 3 Ohm. The 5V and 3,3V power line was killed as well, but that is not a problem. A new LDO 3,3V and 5V 7805 is already ordered.
Replacing the PIC18F87K90 is necessary but that makes no sense without having the HEX dump of the new controler.
Does anybody have such a power supply and could do a HEX dump of the Flash and EEPROM memory?
...04-12-2025, 10:38 AM
Comment