Lucesco Halley (Richard Sapper) Lamp PSU

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • nock
    New Member
    • Jun 2013
    • 1
    • United States
    #21
    Re: Lucesco Halley (Richard Sapper) Lamp PSU

    Hey, I'm a noob, but I have the exact same problem as Syn-Fi (only half of the LED's light up). The other half flickered for a few months before going dead, but now there's nothing from that half of the panel. In addition, there is no brightness adjustment to the remaining lit LEDs. Please let me know if you find a solution.

      Comment

      • kc8adu
        Super Moderator
        • Nov 2003
        • 8832
        • U.S.A!
        #22
        Re: Lucesco Halley (Richard Sapper) Lamp PSU

        one led in the dead half went open.dvm in diode test will find it.
        my gut tells me these things were built too cheap and the led's run too hot.and to make matters worse they seem to be china cheapies.

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • vestaviascott
            Epson 5040UB Projector No Lamp Strike Stuck in Startup - Blinking Status/Lamp Lights
            by vestaviascott
            Hoping someone here can put me on the right track. I'm trying to troubleshoot/flowchart the "internal projector error" on my newly acquired Facebook Marketplace bought Epson 5040UB projector (3LED, not DLP). Owner said it needed new lamp, actually error code blink pattern indicates "Internal Projector Error, call Epson support". Unit is out of warranty as of 8/19

            Here's what happens:

            1) Power on
            2) Blue power indicator lights and the lens cover motor opens the lens cover, light fan noise heard
            3) Blue status light flashes for appx 4 minutes...
            07-29-2020, 06:08 AM
          • AJ847.63e
            BenQ TH681 Originally overheating now wont fire the lamp - Colour wheel not starting
            by AJ847.63e
            Hi All.

            Does anyone have any reference materials or something I can use to try troubleshooting a BenQ TH681? Google unfortunately has turned up zip. I did find a service manual for a W series BenQ but that is pretty much useless, it's more a glorified user manual. A list of voltages would be great as I suspect my mainboard is faulty, the colour wheel voltage is not dipping like it should.

            The one I am troubleshooting now was originally overheating after a lamp replacement. It originally would take 2 minutes or so for it to shut off and blink the temp and lamp lights...
            09-18-2023, 06:42 PM
          • mikey5791
            Help on Samsung Syncmaster T220 dead ccfl lamp
            by mikey5791
            Hi,

            This monitor previously is my main working monitor which i have been using for 8~9 years. Yesterday, when i switched on my pc from fresh to power on, the monitor is just black no display. I started dismantle to look inside the monitor power board but nothing looks suspicious or burnt. So i took my external ccfl inverter to try to power the monitor ccfl lamps which consisted of 2 lamps on upper part and 2 lamps on the lower part.

            Found out the upper ccfl lamp which is supposed to connect to cn304 on the power board did not light up. Then i installed a used working...
            10-18-2020, 03:17 AM
          • khelane
            test active pfc power with lamp test
            by khelane
            Hello
            I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
            Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
            Is there a way...
            06-03-2025, 01:00 AM
          • Yanleb
            Sharp LC-60LE810UN Lamp Error
            by Yanleb
            Hi all,

            I have this Sharp LC-60LE810UN that stays off and blinks a Lamp Error (1 long flash followed by a short flash, in a loop).

            I already confirmed that the first backlight strip has an open LED using a LED strip tester. The other 3 LED strips are fine.

            Before tearing the LCD panel apart, I want to make sure that the rest of the TV set is good. I've tested the power-supply/LED inverter board by sending 5 volt to PS-ON, to PNL-POW (that commands power the T-CON board only), OFL and STB pins. The power-supply is good.

            I've tried all the key...
            08-24-2021, 11:48 PM
          • Loading...
          • No more items.
          Working...