im looking for help with this one, its locket with password and couldn't find another file for this motherboard
mother model 6-71-w13e0-d02 (w130exmb-0D)
thanx in advance
mother model 6-71-w13e0-d02 (w130exmb-0D)
thanx in advance
-
-
Re: Bangho bes-1308
--------------------------------
Password: 41667555
--------------------------------
4 - four ( number )
1 - one ( number )
6 - six ( number )
6 - six ( number )
7 - seven ( number )
5 - five ( number )
5 - five ( number )
5 - five ( number )
--------------------------------
In Laptop: Type the password and press <Enter>.Comment
-
-
Re: Bangho bes-1308
try this biosComment
-
Re: Bangho bes-1308
I posted a virgin bios for a clevo W130EV ,thats what your backup is from,so maybe its the wrong one see the picture.
I found a bios on a "paid" site, "Clevo W130SV - 6-71-W13e0-D02 - W130ExMB-0D"
Try the W130SV bios here: https://repo.palkeo.com/clevo-mirror/
login username: repo
password: repo
The bios is 12MB it will need cutting into 8MB and 4MB using a hex editor.The bios is split accross 2 X chips. Do you have a chip at U32 already ?
.Attached FilesLast edited by SMDFlea; 11-02-2021, 09:38 AM.Comment
-
-
I believe Chip 2 is BIN is the main one as it contained the Windows product key, marked with XXXXX for now.
SN: PF3G1REP
MODEL: 20KW-00J1AU
PROBLEM: Turns on blank screen, charging circuitry motherboard looks good. I have tried another firmware here - but resulted in 5V will not go to 20v due to different PD firmware I believe - using the current firmware it does go to 20V.
Requesting a firmware clean/BIOS region cleaned. Here is output from ME Analyzer:
╔═══════════════════════════════════════════╗... -
I have a Vizio M43-C1 stuck in a reboot loop with no backlight.
I've tested all the voltage rails coming out of the power supply and they are "normal" for this model (PS_ON & DIM go high when turned on, BL_ON & 3D_ON are close to zero due to backlight power flowing through the mainboard, 5VSB is 5V, and 12V is 19V, which is apparently normal for this board).
Basically, I get similar results to Garry in this post: https://www.badcaps.net/forum/showthread.php?t=80346
So, I've ruled out the PSU for now.
The reboot loop... -
i dont know what im doing I have CH341A programmer and SPI programming cable from chipsetpro.com the curent serial number is FVFWQ1CJHV2F and the MLB number i dont know and the motherboard id is 820-00840-A
Can somebody please help.
I dont know how to uplode the .bin file -
Hi i have a smd part with probably mark "QO 11" or "Q0(zero) 11" on it, and its package is SOT89, i doubt its KTB1260 PNP transistor, but in measuring with diode mode of multimeter it shows number 1.4 between emitter and collector pins and its not open circuit, and .59 from collector to base and .8 from emitter to base , and these numbers doesn't match a pnp transistor, i couldn't find any part number and datasheet for it, does anybody have information for that part number?
I've attached pics of this part
Thanks... -
I have an EliteBook x360 1030 G3 and after a motherboard replacement, I want to change the serial number and the FeatureByte. None of the known methods work. MPM is locked and cannot be unlocked via EFI.
Therefore, I read out the two chips and adjusted the serial number, FeatureByte, and Born Date using a hex editor. Now the system won't start anymore. I think I did something wrong with the FeatureByte, as there was a message indicating that the file size was changing.
My serial number is: 5CD849BL7Q
FeatureByte:3X476J6S6b7B7H7M7R7W7maBaEapaqauawbVbhcAd6dUdpdq...
Comment