iPhone 11 Error -1

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Instafixx
    Badcaps Veteran
    • Jul 2022
    • 374
    • India
    #1

    iPhone 11 Error -1

    Helllo Everyone, Namaste.

    I have an iphone 11. The client was doing an OTA updae and the phone crashes and it is stuck in recovery mode. While trying to restore again was getting an Error 3194.

    We removed the NAND and used JCID P13 to format and restore the data. Now when we try to restore it via itunes or 3uTools we get an error -1.

    It sometimes gives the error halfway through or sometimes at the end

    at about 96% when doing via 3uTools
    Restoring Firmware when doing via iTunes.

    One more weird thing is that the device will simply not go into DFU mode at all. It is stuck at recovery mode only.

    Sharing a screenshot of the error at 3uTools. Its a parseregex error everytime.
    Attached Files
    Tags: None
    • mon2
      Badcaps Legend
      • Dec 2019
      • 14673
      • Canada
      #2
      Re: iPhone 11 Error -1

      Not sure if you have seen this video?

      https://www.youtube.com/watch?v=STnpmyMNWJ4

        Comment

        • Instafixx
          Badcaps Veteran
          • Jul 2022
          • 374
          • India
          #3
          Re: iPhone 11 Error -1

          Originally posted by mon2
          Not sure if you have seen this video?

          https://www.youtube.com/watch?v=STnpmyMNWJ4
          The points are fine. Even if we are doing software with just the upper board getting an error too

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Sus256
              HISENSE 65E7KQ PRO - no boot
              by Sus256
              Hi all!

              HISENSE 65E7KQ PRO
              RSAG7.820.13512 - chassis
              MT9618BAATAB - cpu
              RSAG7.820.12059 - power
              HD650Y3U77 - panel
              KLM8G1GETF - emmc

              The TV does not turn on, the standby indicator is on. All voltages are present.
              Emms is dead. Not readable, not detected.
              Replaced emmc.
              But with another dump there is no launch

              Terminal log

              UART
              <
              AC_ON
              RPMB key is not yet programmed

              HASH1_VERSION=0x00000000 64bit
              E-B
              FDE enabled
              layout pattern onebin by SAR7,0...
              06-01-2025, 02:11 AM
            • AJ847.63e
              Has anyone Managed to ever solve DFU Restore error AM Restore Error Domain error75?
              by AJ847.63e
              Hi All,

              Judy doing some research on whether anyone's ever been able to resolve this. Seen quite a few examples and most have just gone eh guess it's dead, but surely there's something we can try?

              For instance, I'm working on a 2020 now with this error. Logiwiki says error 75 occurs when the system is in recovery mode but when I connect it to apple configurator it does show up as DFU so that doesn't seem right. When I try to restore it gets up to step 4/4 and the bar gets to the S of system then that's where it gives that code. Apple configurator then sits on "apple...
              06-02-2023, 12:12 AM
            • sushilachuthan
              APC UPS error P13
              by sushilachuthan
              one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
              the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
              The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
              We replaced the SCR with new device,, but the device is not power on as expected.

              Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....
              09-26-2025, 09:00 AM
            • Superbee_dad
              Sharp 80” long short flash backlight error - Help
              by Superbee_dad
              Hello Sharp TV experts
              Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

              > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
              > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
              01-24-2025, 11:51 PM
            • dbuergi
              Water damaged MacBook Air A1932 AmrestoreErrorDomin Error-9 trying to restore with configurator
              by dbuergi
              Hi all,

              this Macbook was stuck at 5v and didn't start because of some water damage. I was able to clean everything and the board started. So i put everything back together and the Macbook seems to boot with 20v, 1,4A and 29W. So i decided a DFU recovery. At 50% of the system repair i get the error massage from the title. Display stays black and no Apple logo. Both repair and recovery don't work.
              Is there anything i can do?
              11-19-2024, 09:27 AM
            • Loading...
            • No more items.
            Working...