LVDS side converters. Also, Q about LED power pull

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Uranium-235
    Comrade Glimmer
    • Aug 2007
    • 5042
    • US
    #1

    LVDS side converters. Also, Q about LED power pull

    I'm about to put an original LG gaming screen from a ROG gamers dead laptop, into an i3 acer. Both 17.3". Would the higher quality and brighter screen pull more from the LVDS LED power circuits or do they all have a standard power requirement?

    I found a video from laptopscreen.com about using a converter ribbon cable to get the plug to the other side as, well, it is on the other side. Is this a good idea? Even a generic screen here is ~$50-70
    Cap Datasheet Depot: http://www.paullinebarger.net/DS/
    ^If you have datasheets not listed PM me
    Tags: None
    • mcplslg123
      Badcaps Legend
      • Jun 2015
      • 7262
      • india
      #2
      Re: LVDS side converters. Also, Q about LED power pull

      Go ahead as long as the screen is supported. Power requirement is more or less same of an led screen.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • howardc64
          A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
          by howardc64
          Problem

          This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
          08-04-2024, 10:36 PM
        • flibidy
          Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
          by flibidy
          I have here a Magnum IA.100 which belongs to my parents.



          The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


          Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


          What Ive done........
          Magnum IA.100 Front
          8 Photos
          01-01-2025, 01:26 PM
        • ashyt16
          Toshiba TV bad panel half screen dark - pull tabs or not?
          by ashyt16
          Hi fellas, I have a Toshiba 50u6863db (vestel crap) here belonging to a family member.
          The TV was given me to repair (possibly) as it had developed a blank screen, just back lights and sound.

          Upon further investigation it turned out one of her cats had sprayed on the screen as I could see it on the edge of the panel and tabs and it stank. Looks like it probably shorted the circuitry. I cleaned it up and still the same.

          I initially suspected Tcon board as none of the test points were showing correct voltages. Tried removing one LVDS cable at a time, same result....
          10-26-2020, 05:47 AM
        • NolesFan
          Samsung un82ru88000f - Boot loop sort of but can correct with taping of LVDS ribbon
          by NolesFan
          Hello all... TV started boot looping. Opened the back panel and tried to isolate the problem. Just PSB no boot loop. PSB and MB no boot loop. Plug in the LVDS from panel to MB and boot looping starts up. It doesnt matter of order that I plug the LVDS ribbons back in, only 1 and no boot loop but as soon as 2nd one plugs in boot looping. I then noticed a flicker on the screen when I was closing the clip on the harness to the LVDS. Shut the lights off so I can see better, and I noticed as i slowly close it, I will get a picture, but as soon as it clips in, I lose picture and booting happens. So I...
          2 Photos
          10-24-2024, 06:36 PM
        • ttmi100x
          HANNSG Hi221 -- 2 secs to black feat. CCFL flicker & "burn" marks on power board
          by ttmi100x
          Greetings everyone,


          I have a HANNSG Hi221 monitor that exhibits two seconds to black issues (backlight goes off, display is still on as confirmed by shining a flashlight on it) with some additional oddities...


          The monitor failed on me with a standard "2 seconds to black" some time ago prompting me to initially replace most of the electrolytic capacitors (some of them were bulging/leaking).
          Things kinda sorta worked for a night, then the problem returned along with some flickering and "buzzing" noises.

          Upon closer inspection...
          "Burnt" resistor
          6 Photos
          07-31-2024, 06:36 PM
        • Loading...
        • No more items.
        Working...