Touch -IC request EX5440-CG11 egalaxy buy ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Richi_el
    Senior Member
    • Nov 2013
    • 95
    • Koln
    #1

    Touch -IC request EX5440-CG11 egalaxy buy ?

    Hello ,
    Somebody know where i can order this IC ? EX5440-CG11 (See pic)
    It is a TouchController for a device...

    I found the manufactor but i couldnt find 1 seller.....

    I only could found some informations of manufactor:
    http://www.eeti.com/EXC3000_1000.html

    Thanks for reply..
    Attached Files
    Tags: None
    • SMDFlea
      Super Moderator
      • Jan 2018
      • 20481
      • UK
      #2
      Re: Touch -IC request EX5440-CG11 egalaxy buy ?

      They have a distributor in germany,contact them, or get a donor board . https://www.hy-line.de/linecard/hersteller/hcc/11-eeti/
      All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

        Comment

        • Richi_el
          Senior Member
          • Nov 2013
          • 95
          • Koln
          #3
          Re: Touch -IC request EX5440-CG11 egalaxy buy ?

          Hello,
          thanks for your tip, today i had contact with them but the minimum order quantitie is 5000pcs
          so i need round about 50 - 100pcs....
          maybee the is another option ?

            Comment

            • SMDFlea
              Super Moderator
              • Jan 2018
              • 20481
              • UK
              #4
              Re: Touch -IC request EX5440-CG11 egalaxy buy ?

              If you can`t find a seler ,and the distributor won`t sell you a single ic then only option is a donor board, if you can find one .
              All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

                Comment

                • Richi_el
                  Senior Member
                  • Nov 2013
                  • 95
                  • Koln
                  #5
                  Re: Touch -IC request EX5440-CG11 egalaxy buy ?

                  Hello, many thnx i found a seller wich can offer me from china
                  thanks for your support.

                  Regards

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • Prott
                      Surface Pro 4/5 - no touch after LCD change
                      by Prott
                      Hello,
                      I have a question that's driving me a bit nuts recently.

                      Is the touch board on Surface Pro 4/5 somehow married to the motherboard? I have a few Surfaces that, after the touch board change, lost all touch functionality.

                      - I tried flashing the bios (simple ME clean from a known good bios, previous bios didn't have an intergrated hub enabled), reinstalling firmware, reinstalling windows and even new touch boards.
                      - In one instance, after I tried to troubleshoot by using a known good screen + touch pcb combo on a Surface that lost touch, the touch board...
                      01-25-2023, 12:42 PM
                    • howardc64
                      MBP A1989 Touch Bar sometime sluggish touch response
                      by howardc64
                      Had flickering touch bar display. Replaced. Now have an intermittent touch reponsiveness. It generally works but sometimes a press would not respond and need to touch again... sometimes more than 1-2x. Generally happens when trying to go faster on the touch bar and seem more common in certain regions on the bar.

                      Closer inspection reveal L5100 (touch sensor power rail coil) had overheated in the past. Perhaps it can't supply voltage or current properly. Don't have component available so thinking just replace with 0.1mm wire. Touchbar works now but touchbar just have some sluggishness...
                      07-24-2024, 01:42 PM
                    • iprotech
                      Surface Pro 5/6 Touch Issue
                      by iprotech
                      Started with a surface pro 5 repair with battery not fully disconnected and ended with dead touch. Tested with a new touch module and new cable and there still is no touch.
                      Measured touch power rails 1v8 and 5v, both are present.

                      From schematics and boardview it seems like everything happens over SPI, the i2c is NC
                      The MOSI goes directly to the CPU through a 10ohm resistor
                      MISO also goes to CPU through a 10 ohm resistor but also goes through some buffer/level converter chip (VC125) for SPI sniff im guessing for panel brightness level.
                      I do not have a scope,...
                      05-01-2024, 12:54 PM
                    • trepachka
                      Converting HP EliteBook 840 G7 non-touch to touch if possible
                      by trepachka
                      I am trying to convert a HP EliteBook 840 G7 notebook from a non-touch to a touchscreen. I purchased a complete touch LCD assembly with a screen/back cover/bezel/video cable and swapped it out with the original non-touch LCD assembly.
                      The screen works but the touch does not. I know the new LCD assembly is completely functional because we tried it on a similar touchscreen EliteBook 840 G7 and the touch works there.
                      I contacted the seller and he said screen conversion like this will not work due some difference in the motherboard for non-touch and touch capable EliteBook 840 G7.
                      ...
                      04-27-2024, 11:15 PM
                    • AJ847.63e
                      HP Envy X360 13-bf0073TU (6X0Q8PA) Touch Screen Compatibility. Screen P/N N15665-001 - BOE NV133WUM-A65
                      by AJ847.63e
                      Hi All,


                      We've got a HP Envy 12th gen that has been dropped and the LCD panel itself has cracked. The glass is fine just the panel itself is cracked. We ordered a replacement screen assembly using the part number off the HP part surfer website.
                      Upon installation the touch screen now does not work either in UEFI or win 11. Device manager under the "intel Precise touch and Stylus) menu notes "This device cannot start (code 10) Status_Device_Power_Failure".

                      I've tried all the usual troubleshooting steps like reinstalling the driver, uninstalling...
                      04-04-2024, 05:29 PM
                    • Loading...
                    • No more items.
                    Working...