Scematic/boardview request for iPod touch 7th gen

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Earwigg
    New Member
    • Nov 2024
    • 1
    • USA
    #1

    Scematic/boardview request for iPod touch 7th gen

    Hello all,
    perhaps I'm just too dense but i have not found any documentation on the ipod touch anywhere. i do alot of work on these (about 50/week) and would love docs if anyone has them.
    thanks for looking.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • trepachka
      Converting HP EliteBook 840 G7 non-touch to touch if possible
      by trepachka
      I am trying to convert a HP EliteBook 840 G7 notebook from a non-touch to a touchscreen. I purchased a complete touch LCD assembly with a screen/back cover/bezel/video cable and swapped it out with the original non-touch LCD assembly.
      The screen works but the touch does not. I know the new LCD assembly is completely functional because we tried it on a similar touchscreen EliteBook 840 G7 and the touch works there.
      I contacted the seller and he said screen conversion like this will not work due some difference in the motherboard for non-touch and touch capable EliteBook 840 G7.
      ...
      04-27-2024, 11:15 PM
    • Prott
      Surface Pro 4/5 - no touch after LCD change
      by Prott
      Hello,
      I have a question that's driving me a bit nuts recently.

      Is the touch board on Surface Pro 4/5 somehow married to the motherboard? I have a few Surfaces that, after the touch board change, lost all touch functionality.

      - I tried flashing the bios (simple ME clean from a known good bios, previous bios didn't have an intergrated hub enabled), reinstalling firmware, reinstalling windows and even new touch boards.
      - In one instance, after I tried to troubleshoot by using a known good screen + touch pcb combo on a Surface that lost touch, the touch board...
      01-25-2023, 12:42 PM
    • ebyte64
      Scematic request foe Acer A115-31-C0GQ
      by ebyte64
      Good day everyone.

      May I request a scematic for the Acer A115-31-C0GQ? Board number is NB8609_PCB_MB_V6.
      07-28-2023, 03:22 AM
    • howardc64
      MBP A1989 Touch Bar sometime sluggish touch response
      by howardc64
      Had flickering touch bar display. Replaced. Now have an intermittent touch reponsiveness. It generally works but sometimes a press would not respond and need to touch again... sometimes more than 1-2x. Generally happens when trying to go faster on the touch bar and seem more common in certain regions on the bar.

      Closer inspection reveal L5100 (touch sensor power rail coil) had overheated in the past. Perhaps it can't supply voltage or current properly. Don't have component available so thinking just replace with 0.1mm wire. Touchbar works now but touchbar just have some sluggishness...
      07-24-2024, 01:42 PM
    • iprotech
      Surface Pro 5/6 Touch Issue
      by iprotech
      Started with a surface pro 5 repair with battery not fully disconnected and ended with dead touch. Tested with a new touch module and new cable and there still is no touch.
      Measured touch power rails 1v8 and 5v, both are present.

      From schematics and boardview it seems like everything happens over SPI, the i2c is NC
      The MOSI goes directly to the CPU through a 10ohm resistor
      MISO also goes to CPU through a 10 ohm resistor but also goes through some buffer/level converter chip (VC125) for SPI sniff im guessing for panel brightness level.
      I do not have a scope,...
      05-01-2024, 12:54 PM
    • Loading...
    • No more items.
    Working...