Z585 0x000000A5 setup error win7 win8 help me
-
-
Re: Z585 0x000000A5 setup error win7 win8
please explain more about the error. A photo of the screen would help.
when does it happen?
where does it happen?
what are other symptoms? -
Comment
-
Re: Z585 0x000000A5 setup error win7 win8
OK, that's a genuine BSOD... Now when does that code occur? Is it when using hibernation? If not, then the Windows kernel probably falsely thinks the BIOS is pre-2000-spec. or pre-1998-spec.
Microsoft software products, at least one of them in the past, has been known to have integer-overflow conditions. That can cause a program or the system to report the hard drive being smaller than the actual size, such as "64 GB" on an 80 GB hard drive, or the system to report that the BIOS is Windows 95-era, LOL.
https://en.wikipedia.org/wiki/Integer_overflow#Examples
If it's not an integer overflow, which is less likely with 64-bits, then it looks like some absurd checker that's part of the kernel.Last edited by RJARRRPCGP; 11-17-2017, 03:21 PM.ASRock B550 PG Velocita
Ryzen 9 "Vermeer" 5900X
32 GB G.Skill RipJaws V F4-3200C16D-32GVR
Arc A770 16 GB
eVGA Supernova G3 750W
Western Digital Black SN850 1TB NVMe SSD
Alienware AW3423DWF OLED
"¡Me encanta "Me Encanta o Enlistarlo con Hilary Farr!" -Mí mismo
"There's nothing more unattractive than a chick smoking a cigarette" -Topcat
"Today's lesson in pissivity comes in the form of a ziplock baggie full of GPU extension brackets & hardware that for the last ~3 years have been on my bench, always in my way, getting moved around constantly....and yesterday I found myself in need of them....and the bastards are now nowhere to be found! Motherfracker!!" -Topcat
"did I see a chair fly? I think I did! Time for popcorn!" -ratdude747Comment
-
Re: Z585 0x000000A5 setup error win7 win8
Its all about bios settings.Comment
-
Re: Z585 0x000000A5 setup error win7 win8
Bios help '
Comment
-
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
We replaced the SCR with new device,, but the device is not power on as expected.
Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....09-26-2025, 09:00 AM -
Hello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM -
Hi everyone.
I have a HP Elitebook 850 G8.
Serial: 5CG2324XM0
ProdID 6L8D5EC#ABA
It has a Winbond W25Q256JVEN Chip.
I need to remove BIOS Password.
I made a dump with an CHA341A programmer and NeoProgrammer 2.2.0.10.
Attached my dump.
I also used the HP Unlocker tool to create an unlocked file (I followed the guidelines)
I also downloaded latest HP BIOS Update (SP158137) which includes 3 .bin files. I found the Number T76 in my original dump, so I used: T76_01210000.bin
What I did:... -
Hi,
I have a 2014 vintage Philips 60PFL8708S/12 that suddenly died in the middle of the kids watching a show.
The relevant service manual for the chassis is available here.
The TV no longer powers on, and leaving it powered on for a few minutes results in the layer-1 error with 2 blinks.
When I short the SDM to ground I get the layer-2 error code 53.
The inside of the TV has no damaged components and no swollen capacitors.
In SDM-mode when all the power rails are left on despite entering the protection mode, I tracked down and measured...
Comment