COIL 3,3V. One side 3,3v one side4v

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • gcomputers
    Badcaps Veteran
    • Apr 2013
    • 509
    • Albania
    #1

    COIL 3,3V. One side 3,3v one side4v

    hi i m working with this extensa5230E with black screen . its intel cpu.
    my suspect first is bios , i replaced chip with new MX25l2605d flashed and the same problem black screen.
    when i measure coil i see on 3,3v coil have one side 3,3v and one side 4v .

    Any idea please
    Tags: None
    • meritosari
      Senior Member
      • Oct 2010
      • 774
      • Indonesia
      #2
      Re: COIL 3,3V. One side 3,3v one side4v

      I think you should check feedback resistors.

        Comment

        • keeney123
          Lauren
          • Sep 2014
          • 2536
          • United States
          #3
          Re: COIL 3,3V. One side 3,3v one side4v

          I do not know if you have the schematics? I believe these are them. Have you tried the HDMI port? Also. make sure the ram boards at seated correctly.
          Attached Files

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Ryan.man
              Macbook 2017 with touchbar (A1706) won't turn on after removing the screen
              by Ryan.man
              Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!

              My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.

              This time the original cable broke too close to the screen, it can't be fixed without tearing the screen...
              02-04-2025, 12:23 PM
            • smic717394
              iphone XS turns off when press on screen.
              by smic717394
              Hi,

              I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on...
              07-25-2024, 10:16 AM
            • cheeky2
              MSI GTX 970 4G V316 1.1 Loads of lines across screen suspect memory??
              by cheeky2
              Recently purchased this MSI GTX 970 Gaming 4G graphics card and card shows plenty of lines when booting up to bios and into Windows.
              What are your thoughts memory issue as I don't have that much experience repairing graphics cards?
              I have checked before plugging in card for shorts on the 12V power rails, PEX etc otherwise I wouldn't have plugged the card into the motherboard.
              The screen shuts down if I load the drivers on the card.
              See attached pictures.
              Any thoughts with what is likely to be the issue? I suspect a faulty Samsung memory chip and if so would...
              05-28-2025, 07:49 AM
            • momaka
              KingWin ABT-650MM 650 Watt ATX PSU [PCB: SW8835REV:A]
              by momaka
              For today's thread, I have a KingWin ABT-650MM ATX PSU. Official web page with the PSU specs is still up and can be found here:
              http://www.rmac.kingwin.com/products.../abt_650MM.asp

              I just can't help it when I see a broken / for parts PSU on eBay that's listed for cheap and looks at least somewhat interesting. Well, OK, I won't lie – on the outside, this PSU looks anything but interesting. It's a plain gray box with colorful “spaghetti cables”.




              What mostly drew me into buying it is its 2x PCI-E power connectors...
              03-29-2022, 11:34 PM
            • ipatch
              ipad pro 9.7" blew a SMD component while replacing the screen 🤦‍♂️
              by ipatch
              i have an ipad pro 9.7" (1st gen) A1674 where i replaced the screen, but never attached the screen to the frame/chassis (glued down) due to the ipad being previously dropped so the new screen would never fit in the frame properly. so i need flex/bend the chassis to eventually fix the new screen in properly. so i temporarily just applied blue tape around the edges of the screen to keep it in place. when watching videos with the ipad the screen started flicker, so i though maybe the new quasi cheap amz screen i purchased was going out. so i disconnected then reconnected with power still on,...
              08-24-2024, 02:36 PM
            • Loading...
            • No more items.
            Working...