NM-C511 not posting after BIOS update

[questore]

Hi everyone,
Someone come to me after his lenovo has made a BIOS update and after never posting.
Board is:
NM-C511 rev 1.0
ideapad_s145-15api (Type 81UT)
S/N: PF1WZ2L8

After full removing AC and battery and cmos battery and pressing power button for 30sec the laptop turns on and every LED and power rail comes fine,
CPU is very mildly warming up but reaction to buttons and no display.
Tryed to reflash bios suggested on this forum but nothing changed.
Tryed to reprogram the EC with vertyanov programmer but the following happens.
If I plug in original charger, then the EC programming softver shows : "wrong EC ID" (ID: FFFF)
If i plug in a LAb power adapter with no middle pin then EC gets a valid ID for a second then if again never communicates foth EC ID FFFF
What could be the problem? Is it the EC?

[m1ch43lzm]

Hi, did you try with different BIOS?

https://www.badcaps.net/forum/troubl...10#post3577810

Try the BIOS from post #10
Are you using a clip? Or desoldering the bios? Sometimes when using a clip you may get errors when programming/verifying depending on cable length

After first power on, you should wait around 2-3 minutes to get an image
Also try without RAM installed, if it has onboard ram)

Schematics / board view : https://www.badcaps.net/forum/troubl...view-schematic

[mcplslg123]

AFAIK, this mb dont use AD_ID. So it should show same behaviour in dc supply and adapter.

[questore]

AFAIK, this mb dont use AD_ID. So it should show same behaviour in dc supply and adapter.

Correct, but it acts differently, nevertheless EC cannot be read somehow.

[questore]

Hi, did you try with different BIOS?

https://www.badcaps.net/forum/troubl...10#post3577810

Try the BIOS from post #10
Are you using a clip? Or desoldering the bios? Sometimes when using a clip you may get errors when programming/verifying depending on cable length

After first power on, you should wait around 2-3 minutes to get an image
Also try without RAM installed, if it has onboard ram)

Schematics / board view : https://www.badcaps.net/forum/troubl...view-schematic

Thanks you for the típus.
Im using clip, but verifilying always after write. Never has any problem with clips.
I Will try to wait 2 minutes after flash but since power consumpson stays exactly 0.620 I have stopper. Alsó tryed with onboard rám only but same

[SMDFlea]

Tryed to reprogram the EC with vertyanov programmer but the following happens.
If I plug in original charger, then the EC programming softver shows : "wrong EC ID" (ID: FFFF)

Use the original charger, press the power button once, then connect the programmer.

[questore]

Use the original charger, press the power button once, then connect the programmer.

No change.
Still very stange that two original charger is saying EC ID is wrong when connecting and power supply with the same connector is answering at first correctly.
Of course i have checked the power voltage and the two chargers connector is good.

Also what I have noticed that when I plug any charger the BIOS pin 8 has 1.8V even when the laptop is off.
could this mean that the EC firmware is corrupted?

[mcplslg123]

Very likely yes.

[questore]

I just had a very strange matrix feeling.
A NM-D711 come to me with a very very similar problem. its EC only answers once when I plug it in and never more. it also has BIOS 3.3v on pin #8 even when it is not turned on.
If I order a new IC what are the chance that I will be able to programm it if its empty?

[m1ch43lzm]

Also what I have noticed that when I plug any charger the BIOS pin 8 has 1.8V even when the laptop is off.

This looks normal according to the schematics, on your board BIOS chip is powered from +1.8VALW, that is, always on, see attached picture from page 3 of the schematics
The EC is powered from both +3VALW and +3VS (S0, aka power on), maybe you need both enabled to program EC?

My guess it's a timing issue when programming EC, maybe you can try in this order:
I don't have an EC programmer, but maybe this helps
1. With board unplugged from AC adapter, connect your programmer, make sure GND from your programmer is properly connected to target board
2. Select motherboard, EC type, etc. in your software
3. Press read button on the software
4. plug in AC adapter
5. Press power button once (maybe it also works with "Novo" button)?

If successful, repeat the above steps to write EC firmware

Or, from post #9 on here: https://www.badcaps.net/forum/troubl...66#post1585966

Re: Question about replacing IT8586e IO .

are you using vertyanov? there is one way for this programmer to read kbc (ite) properly. just plug in the mainboard immediately after clicking the check connection button.

The other way is if you desolder the EC and program it externally

its EC only answers once when I plug it in and never more. it also has BIOS 3.3v on pin #8 even when it is not turned on.
If I order a new IC what are the chance that I will be able to programm it if its empty?

See above, the BIOS likely is also powered from an always on 3.3v line

A new/blank EC, likely you can program fine, or program externally before soldering to the motherboard

I also saw another post of yours when you mentioned electrical interference, maybe you can try installing your programmer in another PC? (preferably a laptop running on battery power, to rule out a possible grounding issue) Sometimes those electrical faults cause random issues

[mcplslg123]

Most of the lenovo mb's will program ITE ec on 1st boot on its own as long as EC is blank.

[questore]

Most of the lenovo mb's will program ITE ec on 1st boot on its own as long as EC is blank.

Thanks, in the end case I will try it.

[questore]

This looks normal according to the schematics, on your board BIOS chip is powered from +1.8VALW, that is, always on, see attached picture from page 3 of the schematics
The EC is powered from both +3VALW and +3VS (S0, aka power on), maybe you need both enabled to program EC?

My guess it's a timing issue when programming EC, maybe you can try in this order:
I don't have an EC programmer, but maybe this helps
1. With board unplugged from AC adapter, connect your programmer, make sure GND from your programmer is properly connected to target board
2. Select motherboard, EC type, etc. in your software
3. Press read button on the software
4. plug in AC adapter
5. Press power button once (maybe it also works with "Novo" button)?

If successful, repeat the above steps to write EC firmware

Or, from post #9 on here: https://www.badcaps.net/forum/troubl...66#post1585966


The other way is if you desolder the EC and program it externally


See above, the BIOS likely is also powered from an always on 3.3v line

A new/blank EC, likely you can program fine, or program externally before soldering to the motherboard

I also saw another post of yours when you mentioned electrical interference, maybe you can try installing your programmer in another PC? (preferably a laptop running on battery power, to rule out a possible grounding issue) Sometimes those electrical faults cause random issues

Hmmm might be a good idea to not check the connection but to directly read the EC at first time.
Number 5 on the list is not an option in here since power button is in the keyboard and I'm using keyboard connector to flash but on other modells might be good idea thank you.

[questore]

This looks normal according to the schematics, on your board BIOS chip is powered from +1.8VALW, that is, always on, see attached picture from page 3 of the schematics
The EC is powered from both +3VALW and +3VS (S0, aka power on), maybe you need both enabled to program EC?

My guess it's a timing issue when programming EC, maybe you can try in this order:
I don't have an EC programmer, but maybe this helps
1. With board unplugged from AC adapter, connect your programmer, make sure GND from your programmer is properly connected to target board
2. Select motherboard, EC type, etc. in your software
3. Press read button on the software
4. plug in AC adapter
5. Press power button once (maybe it also works with "Novo" button)?

If successful, repeat the above steps to write EC firmware

Or, from post #9 on here: https://www.badcaps.net/forum/troubl...66#post1585966


The other way is if you desolder the EC and program it externally


See above, the BIOS likely is also powered from an always on 3.3v line

A new/blank EC, likely you can program fine, or program externally before soldering to the motherboard

I also saw another post of yours when you mentioned electrical interference, maybe you can try installing your programmer in another PC? (preferably a laptop running on battery power, to rule out a possible grounding issue) Sometimes those electrical faults cause random issues

Tryed your suggestion to read right the first time when pluggin charger and the reading progress bar was very slow but gone till the end, the full reading was empty "FF"
Either something was erased the EC and it cannot be reprogrammed anymore or it is dead.
Also tryed to write with the sam method but since it erases before write, it never got to writing since after erase it lost contact.
Also strange that whenever i got a EC ID that seems corrupt: 8CFF rev -> FF

I think it time to order a new EC