Board problem

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • lord
    Badcaps Veteran
    • May 2011
    • 319
    • Croatia
    #1

    Board problem

    It is a desktop board VB7001, i have 30 pcs of them with 2 kinds of error.
    First one is that board boots but: i push the power button, bios code stops at 00, the i hit the reset button and the board boots. I changed VIA VT1211, ICS 88060 and 6535CBZ.
    Second error: there is no nortbridge voltage, but i didn't have a chance yet to strugle with it. Hopeing there will be some help on the first error....
    Tags: None
    • ben7
      Capaholic
      • Jan 2011
      • 4059
      • USA
      #2
      Re: Board problem

      Originally posted by lord
      It is a desktop board VB7001, i have 30 pcs of them with 2 kinds of error.
      First one is that board boots but: i push the power button, bios code stops at 00, the i hit the reset button and the board boots. I changed VIA VT1211, ICS 88060 and 6535CBZ.
      Second error: there is no nortbridge voltage, but i didn't have a chance yet to strugle with it. Hopeing there will be some help on the first error....
      What type of bios is it? (I.E. Pheonix, Insyde...)

      Did you try flashing the bios?

      Get some pics please!

      There might be a bad voltage regulator for the northbridge chip.

      -Ben
      Muh-soggy-knee

        Comment

        • lord
          Badcaps Veteran
          • May 2011
          • 319
          • Croatia
          #3
          Re: Board problem

          Still didn't had a chance to olay with it. When i do, i will post then news.
          Thank you for your reply!

            Comment

            Previous template Next

            Related Topics

            Collapse
            • huj3r
              Sony KDL-40Z4500 LCD with stripes and 9 blinks (possible BGC board or harness problem
              by huj3r
              Hi there!

              I have a Sony Bravia KDL-40Z4500 which shows a colored vertical stripes pattern when turning on, with a central black shadow that slowly dissipates within the first 10 seconds.

              Photo of the situation after the black shadow dissipates:

              After this behavior the red LED will blink 9 times, then pause for a bit, and blink again 9 times, in a loop.

              I checked the manual (available here) and this corresponds to "HFR error", quoting from the manual:

              > This indicates HFR Communication error. [ HFR Communication...
              08-15-2023, 10:55 AM
            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              ORIGINAL POWER SUPPLY BOARD
              7 Photos
              11-22-2024, 01:46 PM
            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • m1ch43lzm
              HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
              by m1ch43lzm
              Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
              Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
              05-12-2025, 08:37 PM
            • jb_Bak
              Sony xbr-65x900c main board issues?
              by jb_Bak
              Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.

              Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
              Power Board Connector that goes to Main board
              CN6401
              Pin 01 NC
              Pin 02 NC
              Pin 03 "BL_ON": 0V
              Pin 04 "N/C"
              Pin 05 "STBY 3.3V": 3.5V
              Pin 06 "GND": N/C
              Pin 07 "AC_OFF"...
              09-27-2021, 04:52 PM
            • Loading...
            • No more items.
            Working...