Help with mosfet knowledge

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ohspecial1
    New Member
    • Feb 2021
    • 2
    • united kingdom
    #1

    Help with mosfet knowledge

    Hi Folks

    Wonder if you can help

    my mosfet knowledge is not great

    so this is my question

    19v in

    1234 pins on mosfet 1= 19v
    5678 on mosfet 1 ==0v

    mosfter 2 12345678= 0v

    Now im guessing because 1 of the mosfet 1 legs has to have voltage
    Mosftet 2 is fine but no being turned on

    So is mosfet 1 faulty
    Tags: None
    • Sephir0th
      Badcaps Legend
      • Oct 2020
      • 1262
      • Germany
      #2
      Re: Help with mosfet knowledge

      You must not oversimplify things like that. Even if it is "just" about a Mosfet. Sondirstbwe need to know about which particular circuit you're talking.
      FairRepair on YouTube

        Comment

        • mcplslg123
          Badcaps Legend
          • Jun 2015
          • 7262
          • india
          #3
          Re: Help with mosfet knowledge

          pin 1-2-3 is source
          pin4 is gate
          pin 5-6-7-8 is drain

          Set your multi meter in ohms mode(200K or higher) and then meaure resistance between

          Source-gate
          Source-Drain
          Gate-drain

            Comment

            • ktmmotocross
              Boardkiller
              • Feb 2014
              • 3577
              • slovakia
              #4
              Re: Help with mosfet knowledge

              wanna component knowledge? than READ TFK DATASHEET

                Comment

                Previous template Next

                Related Topics

                Collapse
                • Jane
                  How do you test MOSFET in laptops ?
                  by Jane
                  I tried to use this method:

                  Testing an N-channel MOSFET:

                  Step 1: Discharge the Gate (turn off the MOSFET)
                  Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
                  Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

                  Step 2: Charge the Gate (turn on the MOSFET)
                  Now, place the red probe on the Gate (G) and the black probe on the                  ...
                  09-27-2024, 03:31 AM
                • Nooy
                  VGA MOSfet permanently shorted and loss of MOSfet pad
                  by Nooy
                  Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

                  I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
                  02-14-2024, 02:26 AM
                • AppleLover123
                  Asus X712EA 3 volts after the first mosfet
                  by AppleLover123
                  Hey guys,

                  i have a asus motherboard here and as the title says after the first mosfet (in the picture) there is nothing more than 3.15v.
                  I injected 19v and max. 1 amp at the charging port and there is not voltage drop or smth. It's just taking 19v and 1 milliamp.
                  Then i tried to inject 19v and max 1amp after the current sensor and there it first takes 19v and 4 milliamps and after 2 seconds it is taking nothing (no current).
                  I measured on the coils on board everything seems fine. Also the main power rail is not shorted (infinite resistance).
                  Now i thought something...
                  12-15-2024, 07:49 AM
                • MicroSMD Lab
                  ASUS ROG Zephyrus GPU Mosfet repeat failure
                  by MicroSMD Lab
                  The board number is GU502DU. I repaired this a couple weeks ago and it came back with the same issue, same mosfet failed (PQH9201). I'm hoping that the GPU was spared this time.
                  I used the same replacement part (purchased from Mouser) and I'm certain the soldering was done properly since it took just as much effort to remove as before. What could cause this same mosfet to fail? I'm thinking if it was unsuitable then the others would fail too. I looked for similar failures on YTube and the mosfet was replaced with AOE6930 in one instance and AOE6932 in the other but it's possible that the...
                  01-10-2024, 06:36 AM
                • Scotchmist
                  Asus GA502D keeps blowing mosfet
                  by Scotchmist
                  I have an Asus GA502D, it had a blown mosfet which I replaced and the laptop booted into windows, a few mins later it shut off, the same mosfet was blown. I thought maybe just a bad mosfet but same thing happened again, a few mins in windows and shuts off.

                  I have removed the mosfet and can run the laptop no problem

                  The MOSFET is FDPC5018SG

                  Can anyone point me in the direction of what could be the cause of this, could it be the controller rt3663bc?

                  Thanks
                  08-24-2024, 02:23 PM
                • Loading...
                • No more items.
                Working...