Could someone add mac address becouse there are only FFFFFFFFFFFFF
Thanks
it can be 8CDCD43377E8
Thanks
it can be 8CDCD43377E8
-
Last edited by zenek_19; 10-06-2020, 05:52 AM. -
Re: HP 800 G1 TWR missing mac address
Try these intel MAC address tools.If it doesn`t work try the intel mac address tools from ASRock - https://www.asrock.com/support/download/mactool.aspLast edited by SMDFlea; 03-01-2021, 11:32 AM. -
Re: HP 800 G1 TWR missing mac address
OK thanks MAC changer from ASROCK working.Comment
-
Re: HP 800 G1 TWR missing mac address
hi to all, i would also need a little help in changing MAC, can you please give me a little walk ?Last edited by SMDFlea; 05-18-2022, 03:58 PM....the quieter you become the more you are able to hear...Comment
-
The files that are programmed have a MAC address but the network still doesn't work.Comment
-
Due to a lack of donations, server free space at a critical level, and possible closure of Bios Requests all donations are welcome, click:
>>>>> https://www.badcaps.net/index.php?pageid=donate1 <<<<<
Every donation made will go towards server fees and maintenance costs.Comment
-
Hi,
Recently I got this Asrock 970 PRO3 board from scrap. It had a few missing caps under the NB which I've replaced. Sadly, one of them went short (NC597 from boardview file). I did replace it and there doesn't seem to be any shorts left, but the board is not executing POST nor beep codes. I once got it to POST after I was slightly bending it, but that was only once. I tried to redo the same steps but to no avail. All caps on the backside of NB have 22-ish ohms.
I have traced the problem to an dead Northbridge VRM. There's no voltage on Phase (pin 8), FB (pin 6), UGATE... -
Hi everyone,
help me please
I have an HL-DT-ST BD-RE GGW-H20N with ROM version: XA02.
When I tried to burn a 25GB Blu-ray disc using ImgBurn, I got an error.
I will share all the details with you, including the disc information.
...Code:HL-DT-ST BD-RE GGW-H20N XA02 (ATA) Current Profile: BD-R Disc Information: Status: Empty State of Last Session: Empty Erasable: No Free Sectors: 12,219,392 Free Space: 25,025,314,816 bytes Free Time: 2715:27:17 (MM:SS:FF) Next
-
Hello everyone,
I’m looking for a full raw 16 MB BIOS dump for an ASRock Z790-CX (DDR5) motherboard.
The board powers on (fans spin, RGB lights on, RAM LEDs active), but there is no display output and the VGA and BOOT LEDs stay lit.
I’m using an Intel i9-14900KF CPU (14th gen), and it seems the BIOS version on my board doesn’t support it yet. I tried to flash the official ASRock BIOS file (renamed .ROM → .BIN) directly using my RT809H programmer, but it didn’t work — monitor stays on but with black screen, so I believe the ASRock update file is not a complete... -
Board had no history of liquid; unsure of drop history, but no signs of damage of any kind worth noting.
Charger sitting at 5v/0a. PPBUS is at 1.9v-0.9v steady cycle (peaks, drains, loops). Confirmed CHGR_EN_MVR is missing, but DCIN was reaching ISL just fine, so replaced ISL--no change at all. Confirmed pp3v8_aon is also missing--and being unsure *exactly* which signal appears first (or if they are simultaneous), I inspected PMU/U8100 area and found no shorts, but also found PP3V8_AON_MPMU_ISNS_VIN missing (not shorted). Replaced U8100 just in case (have had them fail in weird ways),... -
Hi everyone,
I recently acquired this card from a seller who was selling a PowerMac G5 for parts. He mentioned that the video card was probably broken too.
Upon closer inspection, I can tell the reason why it won't work: it's missing a bunch of CAPS! (it's also missing an inductor - 1.0uH).
It's a nice card as it's one of the few AGP cards that will support 2560 x 1600 resolution on a PowerMac G5 using a 30" Cinema Display.
Looking at the card, it appears to be missing the following:
1x 1.0uH inductor - orange square
2x...
Comment