Help identify component

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Scotchmist
    Senior Member
    • Apr 2019
    • 60
    • United Kingdom
    #1

    Help identify component

    Hi, I need help to identify a component on an Asus z390

    I got this board in a job lot and it is missing the component near the caps at the cpu Socket, I have checked other images and this is the same component further down, with r11 written on top, I suspect it's an inductor but unsure.

    Does anyone know what it is and where I can buy one.

    Thanks
    Attached Files
    Tags: None
    • R_J
      Badcaps Legend
      • Jun 2012
      • 9602
      • Canada
      #2
      Re: Help identify component

      It looks like a TAI-TECH TMPA series, but I'm not sure about the markings, It could be 0.11µH (or 11nH)
      Last edited by R_J; 07-22-2019, 09:50 AM.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • momaka
          Corsair CX750M [Model 75-002019] - burned output toroid inductor
          by momaka
          Looks like I may need a little help from the PSU experts (or anyone really! ) I have a Corsair CX750M (Model 75-002019) that I picked up for free about 4 years ago. This is the PSU:



          So here’s what’s strange about this one: it appears to work normally (normal output voltages) and any PC is stable with it. However, after a while (typically 10-20 minutes, but time can vary depending on the load), there is a sweetish smell of burned magnet wire insulation emanating from the PSU. Upon opening the PSU after this happened (many times), I was able to confirm...
          09-19-2021, 08:44 PM
        • Bartoloni
          Lenovo S145 -15iwl vcore inductor warm.. looking with oscilloscope there is a spike.
          by Bartoloni
          Hi, i have a Lenovo S145 that after 20 seconds shutdown and restart (it's working correctly on thse 20 seconds)
          everything seems ok, but on Vcore inductor ( this is an i3 with just 1 switching power supply for CPU)

          there is an output to teh CPU with a spike.. seems that inductor can't handle the input...
          replaced the capacitor (330) and the inductor (R15) without any change
          any idea? very thank you!

          input of the inductor seems as usual... only strange thing is that the upper/lower voltages seems to be 21V (main power line is 19.3) ... but not sure this...
          12-09-2024, 12:42 PM
        • badcap111
          How to read inductor specs?
          by badcap111
          I have a broken samsung galaxy s10 with missing inductor. I want to replace the missing inductor and I have found some vendors. But I don't understand how to read the specifications of the inductor. The specs are:

          INDUCTOR-SMD;470NH,20%,2520,T0.8,0.029OH

          I understand that the inductor is 470 nH with 20% margin, and the size is 2520 or 1008 (imperial measure), but what do T0.8,0.0290OH mean? I can't find any explanation on the web.
          09-12-2023, 01:25 PM
        • silver60618
          Blown Inductor on WD My Passport
          by silver60618
          Hi Guys, my WD My Passport drive powers on, then powers off. Ive taken out the motherboard and identified a blown Inductor. Im trying to recover my data only

          Reading between leads show nothing. If I removed this Inductor, what would be a suitable replacement? am I correct that its a ferrite Inductor is to just filter noise?
          Ive seen people just bridge them, any harm in replacing it with a differnt value Inductor?

          Lastly am I correct in thinking there is no polarity on the smd component?

          Thanks!...
          04-05-2024, 09:54 AM
        • Vanillaboard
          MSI Z390 MPG Gaming Plus wont start. No lights no Fans
          by Vanillaboard
          MSI MPG Z390 Gaming Plus - 15.2V on GPU ATX Connector, Now Board Won't Start

          Hello everyone,

          I was experimenting with my MSI MPG Z390 Gaming Plus motherboard and accidentally applied 12.5V to the GPU ATX connector. The motherboard immediately powered off, and now it won't start anymore.
          The graphics card seems to be fine, so no issues there.

          I've measured the voltage at JFP1, and I'm getting 3.95V, as well as on the PS_OUT# pin of the SuperIO. As far as I know, these should be at 5V in standby, right?
          Now my question is: where exactly do these...
          10-18-2024, 02:40 PM
        • Loading...
        • No more items.
        Working...