My first try AOpen MB

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • kiddznet
    Senior Member
    • Jul 2010
    • 176
    #21
    Re: My first try AOpen MB

    Took a bit of arm twisting to get it to take Winxp but its running sweet now

    Motherboard:
    CPU Type Intel Celeron, 900 MHz (9 x 100)
    Motherboard Name AOpen AX34 Pro II (6 PCI, 1 AGP, 1 AMR, 4 DIMM, Audio)
    Motherboard Chipset VIA VT82C694X Apollo Pro133A
    System Memory 1024 MB (SDRAM)
    BIOS Type Award Modular (02/12/01)


    939 DualCore AMD Opteron, 1800 MHz (9 x 200)
    Abit AN8 / Fatal1ty AN8 SLI Series
    3072 MB (PC3200 DDR SDRAM)
    ATI Radeon HD 4300/4500 Series (1024 MB
    Lian LI Aluminium mesh case

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • corrize
        Best way to solder LVDS connector for beginner (and qfn) ?
        by corrize
        Hello, I'm a beginner for micro soldering. Right now I have some difficult to solder a qfn 20, I guess I put too much solder on the thermal-ground pad, the result is a corner of chip wich don't touch the board (last try).

        I use a wire solder with hot air, I tin the board and chip before with iron and I use good flux.

        I will have to solder a LVDS connector (40 pins, laptop pc), I saw a solder paste in seringe, good quality (it does not scatter).
        See the test :
        https://youtu.be/bNAzC-EvqHs?t=1767

        With hot air from bellow the board, that's...
        03-09-2023, 02:57 AM
      • myth77
        UV solder mask - high temp resistent, recomendation?
        by myth77
        Can someone recommend any good UV solder mask? But i need a solder mask that will stand high temperetures. The thing is...sometimes i have a bigger cooper ripped from the board, lets say mosfet pad... i reconstract it with cooper sheet, then i "glue it" with solder mask...then i use UV light...and let it cool a bit. After, i try to clean the cooper of extra solder mask..and till that part all is ok. But, when i use a soldering iron to solder that pad/cooper...the solder mask gets weaker or destroyed and finally the pad is ripped again from the board .
        Is there any solder mask...
        03-28-2022, 04:04 AM
      • petemanuk
        BGA solder balls not connecting - help pls
        by petemanuk
        So I though in my spare time I’d set myself up repairing motherboards mainly pin damaged lga1151 sockets types.

        I’m using an achi ir sc pro rework station (gave up on my Achie ir6500 - don’t recommend)

        I’ve managed to get my rework profile somewhere in the correct region (after a lot of trial and error) to get the old sockets off and reflow new ones back on again, the problems I’m getting is not all of the solder balls are re-attaching when re-flow occurs. I know this because when socket is removed pads still look clean and have no solder...
        11-16-2022, 05:21 AM
      • acedogblast
        Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
        by acedogblast
        This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

        There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
        11-02-2024, 05:13 PM
      • sircastor
        Solder not reflowing - what am I doing wrong?
        by sircastor
        I'm trying to fix a broken MacBook Air, and got a parts board to salvage components from. Following the suggestions of many folks here, I wanted to get in a little practice of using my hot air station (A Quick 957DW+) on the parts board so I know what kind of behavior to expect.

        For the life of me, I can't get anything done with this thing. I have tried multiple temperatures (from 210-425c), different air speeds, preheating the board (with the hot air, just warming it all around). I have applied what feels like excessive amounts of flux (Amtech V2-TF-559) and the solder on these components...
        03-03-2024, 02:44 AM
      • Loading...
      • No more items.
      Working...